Yandex MC
Elsa online. ElsaWin. ElsaWeb. VWEngine oil: Drain or extract; renew oil filter and replenish engine oil

elsawin online

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru

Attention! Please use superetka.com/elsa

Touareg

Please use
superetka.com/elsa

PLEASE USE https://SUPERETKA.COM/elsa
elsa on kolhosniki not support now!

Engine oil: Drain or extract; renew oil filter and replenish engine oil
Draining or extracting engine oil → Chapter
Draining engine oil in 6-cylinder TSI (hybrid) petrol engine: → Chapter
Renewing oil filter. → Chapter
Replenishing engine oil. → Chapter
Draining or extracting engine oil
  Caution
t  For engines with standing oil filter the oil filter must be renewed before changing the engine oil → Chapter. When removing the filter element a valve is opened, the oil in the filter housing automatically flows into crankcase.
t  The oil drain plug is fitted with a secure seal, therefore the oil drain plug must always be renewed.
Or
    
–  Extract engine oil using used oil collection and extraction unit -VAS 6622A-.
or
–  Remove oil drain plug.
–  Clean M24 oil drain plug and fit new seal. The M14 oil drain plug with integrated seal must always be renewed. → Electronic Parts Catalogue ETKA
–  Let engine oil drain.
  Note
Observe disposal regulations!
–  Screw in oil drain plug together with seal hand-tight and then tighten to specified torque.
–  Replenishing engine oil.
Engine oil capacity:
t  → Maintenance tables
t  Engine oil: capacities and specifications → Chapter
Torque settings:
t  Oil drain plug M14: 30 Nm
t  Oil drain plug M24: 50 Nm
  WARNING
t  Torque specifications must not be exceeded.
t  Excessive torque can cause leaks in the area of the oil drain plug or even damage.
Draining engine oil in 6-cylinder TSI (hybrid) petrol engine:
  Caution
t  In hybrid vehicles, the hybrid-relevant components in the working area must be visually inspected → Chapter
t  In the event of conspicuous findings or uncertainties, contact your responsible high-voltage technician or specialist electrician!
t  For engines with standing oil filter the oil filter must be renewed before changing the engine oil → Chapter. When removing the filter element a valve is opened, the oil in the filter housing automatically flows into crankcase.
t  The oil drain plug is fitted with a secure seal, therefore the oil drain plug must always be renewed.
Special tools and workshop equipment required
   W00-11526
t  Funnel, flexible -VAS 6675-
   W00-10959
t  Used oil collection and extraction unit -VAS 6622-
  Note
To prevent excess contamination of the vehicle from the engine oil, observe the following instructions.
   W00-11526
–  Use flexible funnel -VAS 6675- to drain engine oil.
–  Place funnel on subframe and assembly carrier.
–  Remove oil drain plug.
–  Clean M24 oil drain plug and fit new seal. The M14 oil drain plug with integrated seal must always be renewed. → Electronic Parts Catalogue ETKA
–  Let engine oil drain.
  Note
Observe disposal regulations!
–  Screw in oil drain plug together with seal hand-tight and then tighten to specified torque.
–  Replenishing engine oil.
Engine oil capacity:
t  → Maintenance tables
t  Engine oil: capacities and specifications → Chapter
Torque settings:
t  Oil drain plug M14: 30 Nm
t  Oil drain plug M24: 50 Nm
  WARNING
t  Torque specifications must not be exceeded.
t  Excessive torque can cause leaks in the area of the oil drain plug or even damage.
Renewing oil filter
Renewing oil filter in 6-cylinder TSI (hybrid) petrol engine. → Chapter
Renewing oil filter in 6-cylinder FSI petrol engine → Chapter
Renewing oil filter in 6-cylinder diesel engine. → Chapter
Renewing oil filter in 8-cylinder diesel engine. → Chapter
Renewing oil filter in 8-cylinder petrol engine. → Chapter
Renewing oil filter in 8-cylinder diesel engine
Remove engine cover panel. → Chapter
Special tools and workshop equipment required
t  Socket insert -SW 32-.
Removing
  Note
t  Observe disposal regulations!
t  Oil new O-rings before installing.
–  Cover area around oil filter sealing cap e.g. with oil spill cloth.
   N01-11248
–  Release sealing cap using a 32 mm socket.
–  Remove sealing cap together with oil filter element.
   N01-11051
–  Separate oil filter element -3- from sealing cap -1-.
  Caution
The seals -2- and -4- and oil filter element -3- must be renewed.
–  Clean sealing surfaces on threaded cap and oil filter housing.
Installing
–  Renew oil filter element -3-.
–  Install sealing cap -1- with new O-rings -2- and -4- and tighten to 35 Nm.
The remaining assembly steps are basically a reverse of the dismantling procedure.
Renewing oil filter in 6-cylinder TSI (hybrid) petrol engine
Remove engine cover panel. → Chapter
Special tools and workshop equipment required
t  Socket insert -SW 32-.
Removing
  Note
t  Observe disposal regulations!
t  Oil new O-rings before installing.
–  Cover area around oil filter sealing cap e.g. with oil spill cloth.
   N01-11053
–  Release sealing cap using a 32 mm socket.
–  Remove sealing cap together with oil filter element.
   N01-11050
–  Separate oil filter element -3- from sealing cap -1-.
  Caution
The seals -2- and -4- and oil filter element -3- must be renewed.
–  Clean sealing surfaces on threaded cap and oil filter housing.
Installing
–  Renew oil filter element -3-.
–  Install sealing cap -1- with new O-rings -2- and -4- and tighten to 35 Nm.
The remaining assembly steps are basically a reverse of the dismantling procedure.
Draining oil:
Renewing oil filter in 6-cylinder FSI petrol engine
  Note
t  Observe disposal regulations!
t  Oil new O-rings before installing.
t  Prevent engine oil from dripping onto components in area of engine compartment and running gear.
Perform the following procedure:
   N01-11053
–  Remove oil drain plug -1- of threaded cover and drain oil.
–  Once oil has drained out, screw in drain plug again and tighten to 10 Nm.
–  Loosen threaded cover -2- on hexagon using AF 36 tool insert -1- or around perimeter and remove.
–  Clean sealing surfaces on threaded cap and oil filter housing.
Vehicles without auxiliary heater:
–  Remove oil filter cover with oil filter element between steering gear and front differential.
–  Dispose of used oil filter element in correct manner.
–  Clean sealing surface on engine and oil filter cover.
   N01-11246
–  Renew filter element -4- and seal -3-.
–  Install threaded cap -2- with new O-ring and tighten to 25 Nm.
Vehicles with auxiliary heater:
–  Place oil filter cover between front differential, engine support and sump.
–  Place bag from packaging of new oil filter over old oil filter element and unclip oil filter element from oil filter element.
If new filter is not supplied with a bag, use a suitable cloth.
–  Remove oil filter element between steering gear and front axle.
–  Dispose of used oil filter element in correct manner.
–  Place suitable cloth in opening of oil filter cover, remove oil filter cover downwards and clean.
–  Clean engine sealing surface.
–  Insert new seal in oil filter cover, lubricate lightly and insert oil filter cover back between front differential, engine support and sump.
–  Guide new oil filter element between steering gear and front differential and insert into oil filter cover.
–  Tighten oil filter cover to 25 Nm.
Renewing oil filter in 6-cylinder diesel engine
Remove engine cover panel. → Chapter
Special tools and workshop equipment required
t  Socket insert -SW 32-.
Removing
  Note
t  Observe disposal regulations!
t  Oil new O-rings before installing.
–  Cover area around oil filter sealing cap e.g. with oil spill cloth.
   N01-11247
–  Release sealing cap using a 32 mm socket.
–  Remove sealing cap together with oil filter element.
   N01-11237
–  Separate oil filter element -3- from sealing cap -1-.
  Caution
The seals -2- and -4- and oil filter element -3- must be renewed.
–  Clean sealing surfaces on threaded cap and oil filter housing.
Installing
–  Renew oil filter element -3-.
–  Install sealing cap -1- with new O-rings -2- and -4- and tighten to 35 Nm.
The remaining assembly steps are basically a reverse of the dismantling procedure.
Renewing oil filter in 8-cylinder petrol engine
Remove engine cover panel → Chapter.
Special tools and workshop equipment required
t  Socket insert -SW 32-.
Removing
  Note
t  Observe disposal regulations!
t  Oil new O-rings before installing.
–  Cover area around oil filter sealing cap e.g. with oil spill cloth.
   N01-11053
–  Release sealing cap -arrow- using a 32 mm socket.
–  Remove sealing cap together with oil filter element.
   N01-11243
–  Separate oil filter element -3- from sealing cap -1-.
–  Clean sealing surfaces on threaded cap and oil filter housing.
Installing
–  Renew oil filter element -3-.
–  Install sealing cap -1- with new O-rings -2- and -4- and tighten to 25 Nm.
The remaining assembly steps are basically a reverse of the dismantling procedure.
Replenishing engine oil
Engine oil: capacities and specifications → Chapter
General notes
  Note
t  Observe disposal regulations!
t  The vehicle has no oil dipstick in the engine compartment. The current engine oil level can be called up in the infotainment system screen or can be checked using the oil gauge tester -T40178-.
–  After replenishing with oil, wait at least 3 minutes and then check oil level. → Chapter
   N01-11053

Didn't find what you were looking for? Try to find in:
- Mitchell onDemand online


- ETKA ONLINE - login-pass from kolhosniki.ru

- NEW ELSA ONLINE - login-pass from kolhosniki.ru

This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20