2004-08 ACCESSORIES & EQUIPMENT
Fenderwell - TSX
Front Inner Fender Replacement
NOTE: |
Take care not to scratch the body. |
- Remove the front inner fender (A).
- On the back of the wheel arch, remove the screws (B) If equipped, remove the front splash guard (C) (Canada models).
- From under the front bumper (D), remove the bolts (E) securing the front bumper, splash shield (F), and front inner fender, and remove the clip (G) securing the front bumper and front inner fender.
- From the wheel arch, remove the clips (H, I, J) securing the front inner fender (and splash shield) on the body.
- Release the hook (K) of the splash shield, then remove the front inner fender.
Fig. 1: Identifying Front Inner Fender W/Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Install the inner fender in the reverse order of removal, and note these items:
- Check if the clips are damaged or stress-whitened, and if necessary, replace them with new ones.
- Push the clips into place securely.
Splash Shield Replacement
NOTE: |
Take care not to scratch the body. |
- Remove the splash shield (A).
- From both wheel arch, remove the bolts (B), clips (C), and clip (D) securing the front inner fender (E) and splash shield (on the body).
- From under the front bumper (F), remove the clips (C), and bolts (G).
- Release the hooks (H) of the splash shield, then pull the splash shield out.
Fig. 2: Identifying Splash Shield W/Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Install the splash shield in the reverse order of removal, and note these items:
- Check if the clips are damaged or stress-whitened, and if necessary, replace them with new ones.
- Push the clips into place securely.
Front Fender Fairing Replacement
- Remove the front inner fender as needed (see FRONT INNER FENDER REPLACEMENT
).
- Open the front door. Remove the upper clip, and from inside the door, remove the lower clip securing the front fender fairing (A) and front fender (B).
Fig. 3: Identifying Lower Clip Securing Front Fender Fairing And Front Fender
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- From the wheel arch, release the clips.
Fig. 4: Identifying Wheel Arch Clips
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Remove the front fender fairing (A).
Fig. 5: Identifying Front Fender Fairing
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Install the fender fairing in the reverse order of removal, and note these items:
Rear Inner Fender Replacement
NOTE: |
Take care not to scratch the body. |
- Remove the rear inner fender (A).
- On the front of the wheel arch, remove the screws (B) securing the side sill panel (C) and rear inner fender, and the clip (D) securing the rear inner fender and middle floor undercover (E).
- On the rear bumper (F), remove the screw (G).
- From the wheel arch, remove the clips (H, I).
- Pull the rear inner fender out.
Fig. 7: Identifying Rear Inner Fender
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Install the inner fender in the reverse order of removal, and note these items:
- Check if the clips are damaged or stress-whitened, and if necessary, replace them with new ones.
- Push the clips into place securely.
Rear Air Outlet Replacement
- Remove the rear bumper (see
REAR BUMPER REMOVAL/INSTALLATION
).
- Detach the hooks (A), then remove the rear air outlet (B). Take care not to scratch the body.
Fig. 8: Identifying Rear Air Outlet Hooks
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Install the air outlet by pushing on the hook portions until the hooks snap into place.