2004-08 ACCESSORIES & EQUIPMENT
Interior Lights - TSX
Component Location Index
Fig. 1: Identifying Interior Lights Component Location
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Circuit Diagram
Fig. 2: Interior Lights - Circuit Diagram (1 Of 2)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 3: Interior Lights - Circuit Diagram (2 Of 2)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Front Individual Map Light Replacement
- Carefully pry off the lens (A) with a small screwdriver.
Front Map Light: 8 W x 2
Fig. 4: Identifying Lens, 3P And 10 Connectors And Housing With Mounting Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Remove the two mounting screws.
- Disconnect the 3P connector (B) from the housing (C).
- Disconnect the 10P connector (D) from the ambient light (E).
- Install the light in the reverse order of removal.
Ambient Light Replacement
- Remove the front individual map light (see FRONT INDIVIDUAL MAP LIGHT REPLACEMENT
).
- Carefully pry off the ambient light assembly (A) from the map light housing (B) while pressing in on the retaining tabs (C).
Fig. 5: Identifying Ambient Light Assembly, Map Light Housing And Retaining Tabs
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Install in the reverse order removal.
Ceiling Light Replacement
- Turn the light switch OFF.
- Carefully pry off the lens (A) with a small screwdriver.
Ceiling Light: 8W
Fig. 6: Identifying Lens, 3P Connector And Housing With Mounting Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Remove the two mounting screws.
- Disconnect the 3P connector (B) from the housing (C).
- Install in the reverse order of removal.
Trunk Light Test/Replacement
- Open the trunk lid.
- Carefully pry out the trunk light (A).
Trunk Light: 5 W
Fig. 7: Identifying Trunk Light 2P Connector Terminal
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Disconnect the 2P connector (B) from the light.
- Check for continuity between the No. 1 (+) and No. 2 (-) terminals. There should be continuity. If there is no continuity, check the bulb (C). If the bulb is OK, replace the trunk light.
Trunk Lid Latch Switch Test
- Open the trunk lid.
- Disconnect the 3P connector (A) from the trunk lid latch (B).
Fig. 8: Identifying Trunk Lid Latch 3P Connector Terminal
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Check for continuity between the No. 2 and No. 3 terminals.
- There should be continuity with the trunk lid latch unlatched (trunk open).
- There should be no continuity with the trunk lid latch latched (trunk closed).
- If the continuity is not as specified, replace the trunk lid latch switch.
Vanity Mirror Light Test
- Open the sunvisor.
- Remove the sunvisor (see
HEADLINER REMOVAL/INSTALLATION
).
- Disconnect the 2P connector (A) from the vanity mirror light.
Vanity mirror light: 2 W
Fig. 9: Identifying Vanity Mirror Light 2P Connector Terminal
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Check for continuity between the No. 1 and No. 2 terminals.
- With the vanity mirror cover (B) opened, there should be continuity.
- With the vanity mirror cover closed, there should be no continuity.
- If the continuity is not as specified, replace the bulb (C) or the sunvisor.
Courtesy Light Replacement
- Carefully pry off the lens (A) with a small screwdriver.
Courtesy light: 3.8 W
Fig. 10: Identifying Lens And Bulb
Courtesy of AMERICAN HONDA MOTOR CO., INC.
- Remove the bulb (B) from the socket.