For details of lubrication points and type of lubricants to be applied, refer to the illustrated index and various work procedures (such as Assembly/Reassembly, Replacement, Overhaul, Installation, etc.) contained in each article.
LUBRICANTS AND FLUIDS REFERENCE
Application
Lubricant or Fluid
A
Engine
Acura Motor Oil: P/N 08798-9014 (5W-30) Look for the API certification seal on the oil container. Make sure it says "For Gasoline Engines." SAE viscosity: See chart.
B
Manual transmission
Acura Manual Transmission Fluid (MTF): P/N 08798-9031A Always use Acura MTF. Using motor oil can cause stiffer shifting because it does not contain the proper additives.
Automatic transmission
Acura Automatic Transmission Fluid (ATF-Z1): P/N 08200-9001A
Always use Acura ATF-Z1. Using a non-Acura ATF can affect shift quality.
C
Brake system (including VSA lines)
Acura DOT 3 Brake Fluid: P/N 08798-9008A
Always use Acura DOT 3 Brake Fluid. Using a non-Acura brake fluid can cause corrosion and decrease the life of the system.
D
Clutch system (manual transmission)
E
Shift cable ends (manual transmission)
Honda Silicone Grease: P/N 08C30-B0234M
F
Brake booster clevis pin
Multipurpose Grease
G
Clutch master cylinder clevis pin (manual transmission)
H
Release fork (manual transmission)
I
Battery terminals
J
Fuel fill door
K
Hood hinges and hood latch
L
Trunk hinges
M
Caliper piston boot and seal, caliper pins and boots
Honda Silicone Grease: P/N 08C30-B0234M
N
Power steering system
Acura Power Steering Fluid: P/N 08206-9002A
Always use Acura Power Steering Fluid. Using any other type of power steering fluid or automatic transmission fluid can cause increased wear and poor steering in cold weather.
0
Air conditioning compressor
Compressor Oil: SP-10 (P/N 38897-P13-A01AH or 38899-P13-A01) for refrigerant HFC-134a (R-134a)
P
Cooling system
Acura Long Life Antifreeze/Coolant Type 2: P/N OL999-9011A
Fig. 1: API Certification Seal And Engine Oil Viscosity Chart
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 2: Identifying Lubrication Points
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Maintenance Schedule outlines the minimum required maintenance. Service at the indicated distance or time, whichever comes first. Use the Maintenance Schedule for Severe Conditions if the vehicle meets any of the qualifiers in the Severe Conditions schedule, or if the vehicle is normally driven in Canada.
MAINTENANCE SCHEDULE
Distance
Time
Maintenance Items
10,000 miles
16,000 km
--
Do items in A.
20,000 miles
32,000 km
1 year
Do items in A and B.
30,000 miles
48,000 km
--
Do items in A and C.
40,000 miles
64,000 km
2 years
Do items in A and B.
50,000 miles
80,000 km
--
Do items in A.
60,000 miles
96,000 km
3 years
Do items in A, B, and C.
--
--
3 years
Replace brake fluid (see
BRAKE SYSTEM BLEEDING
). Use Acura DOT 3 Brake Fluid.
70,000 miles
112,000 km
--
Do items in A.
80,000 miles
128,000 km
4 years
Do items in A and B.
90,000 miles
144,000 km
--
Do items in A and C.
100,000 miles
160,000 km
5 years
Do items in A and B.
110,000 miles
176,000 km
--
Do items in A and D.
120,000 miles
192,000 km
6 years
Do items in A, B, C, E, F, and G.
--
--
6 years
Replace brake fluid (see
BRAKE SYSTEM BLEEDING
). Use Acura DOT 3 Brake Fluid.
130,000 miles
208,000 km
--
Do items in A.
140,000 miles
224,000 km
7 years
Do items in A and B.
150,000 miles
240,000 km
--
Do items in A and C.
160,000 miles
256,000 km
--
Inspect idle speed (see
IDLE SPEED INSPECTION
), every 160,000 miles (256,000 km). Idle speed: M/T 750 ± 50 rpm in neutral, A/T 800 ± 50 rpm in IM or P position.
160,000 miles
256,000 km
8 years
Do items in A and B.
--
--
9 years
Replace brake fluid (see
BRAKE SYSTEM BLEEDING
). Use Acura DOT 3 Brake Fluid.
Do the items in parts A, B, C, D, E, F, and G as required for the mileage/time interval listed.
MAINTENANCE SCHEDULE
Part
Maintenance Items
A
Replace engine oil (see
ENGINE OIL REPLACEMENT
) every 10,000 miles (16,000 km) or 1 year.
Engine oil capacity without oil filter: 4.0 L (4.2 US qt).
Rotate tires, and check tire inflation and condition every 10,000 miles (16,000 km).
Follow the pattern shown in the Owner's Manual.
B
Replace engine oil filter (see
ENGINE OIL FILTER REPLACEMENT
) every 20,000 miles (32,000 km) or 1 year.
Engine oil capacity with oil filter: 4.2 L (4.4 US qt).
Check front and rear brakes (see
BRAKE SYSTEM INSPECTION AND TEST
) every 20,000 miles (32,000 km) or 1 year.
Check parking brake adjustment (see
PARKING BRAKE INSPECTION AND ADJUSTMENT
) every 20,000 miles (32,000 km) or 1 year.
Check the number of clicks 6 to 9 when the parking brake lever is pulled with 196 N (20 kgf, 44 lbf) of force.
Inspect tie-rod ends, steering gearbox, and gearbox boots (see
STEERING LINKAGE AND GEARBOX INSPECTION
) every 20,000 miles (32,000 km) or 1 year.
Inspect suspension components (see
COMPONENT LOCATION INDEX
) every 20,000 miles (32,000 km) or 1 year.
Inspect driveshaft boots (see
DRIVESHAFT INSPECTION
) every 20,000 miles (32,000 km) or 1 year.
Check boots for cracks and boot bands for tightness.
Inspect brake hoses and lines including VSA (see
BRAKE HOSE AND LINE INSPECTION
) every 20,000 miles (32,000 km) or 1 year.
Check the master cylinder and VSA modulator-control unit for damage and leakage.
Inspect all fluid levels, condition of fluids, and check for leaks every 20,000 miles (32,000 km) or 1 year.
Inspect exhaust system* (see
EXHAUST PIPE AND MUFFLER REPLACEMENT
) every 20,000 miles (32,000 km) or 1 year.
Check catalytic converter heat shield, exhaust pipe, and muffler for damage, leaks, and tightness.
Inspect fuel lines and connections* (see
FUEL LINE INSPECTION
) every 20,000 miles (32,000 km) or 1 year.
Check for loose connections, cracks, and deterioration; retighten loose connections and replace damaged parts.
C
Inspect drive belt (see
DRIVE BELT INSPECTION
) every 30,000 miles (48,000 km) or 2 years.
Inspect auto tensioner indicator; no adjustment needed.
Replace dust and pollen filter (see
DUST AND POLLEN FILTER REPLACEMENT
) every 30,000 miles (48,000 km) or 2 years.
Replace air cleaner element (see
AIR CLEANER REMOVAL/INSTALLATION
) every 30,000 miles (48,000 km), (independent of time).
D
Inspect the valve clearance (see
VALVE CLEARANCE ADJUSTMENT
) every 110,000 miles (176,000 km), otherwise adjust only if noisy.
Intake: 0.21-0.25 mm (0.008-0.010 in.). Exhaust: 0.25-0.29 mm (0.010-0.011 in.).
Replace spark plugs (see
SPARK PLUG INSPECTION
) every 110,000 miles (176,000 km).
Use IZFR6K11 (NGK) or SKJ20DR-M11 (DENSO).
E
Replace manual transmission fluid (see
MANUAL TRANSMISSION
) every 120,000 miles (192,000 km) or 6 years.
Capacity: 2.0 L (2.1 US qt); use Acura MTF.
F
Replace automatic transmission fluid (see
ATF REPLACEMENT
) at 120,000 miles (192,000 km) or 6 years, then every 90,000 miles (144,000 km) or 5 years.
Capacity: 2.9 L (3.1 US qt); use Acura ATF-Z1.
G
Replace engine coolant (see
COOLANT REPLACEMENT
) at 120,000 miles (192,000 km) or 10 years, then every 60,000 miles (96,000 km) or 5 years.
Capacity: M/T 5.4 L (1.43 US gal), A/T 5.3 L (1.40 US gal); use Acura Long Life Antifreeze/Coolant Type 2.
NOTE:
According to state and federal regulations, failure to do the maintenance items marked with an asterisk (*) will not void the client's emissions warranties. However, Acura recommends that all maintenance services be done at the recommended intervals to ensure long-term reliability.
Use the Severe Conditions schedule if the vehicle is driven MAINLY in Canada or in any of the following conditions; if only OCCASIONALLY driven in these conditions, use the Normal Conditions schedule.
Severe Driving Conditions
MAINTENANCE SCHEDULE
Distance
Time
Maintenance Items
5,000 miles
8,000 km
--
Do item in A.
10,000 miles
16,000 km
--
Do items in A and B.
15,000 miles
24,000 km
--
Do items in A and C.
20,000 miles
32,000 km
1 year
Do items in A, B, and E.
25,000 miles
40,000 km
--
Do item in A.
30,000 miles
48,000 km
--
Do items in A, B, C, and D.
35,000 miles
56,000 km
--
Do item in A.
40,000 miles
64,000 km
2 years
Do items in A, B, and E.
45,000 miles
72,000 km
--
Do items in A and C.
50,000 miles
80,000 km
--
Do items in A and B.
55,000 miles
88,000 km
--
Do item in A.
60,000 miles
96,000 km
3 years
Do items in A, B, C, D, E, F, and H.
--
--
3 years
Replace brake fluid (see
BRAKE SYSTEM BLEEDING
). Use Acura DOT 3 Brake Fluid.
65,000 miles
104,000 km
--
Do item in A.
70,000 miles
112,000 km
--
Do items in A and B.
75,000 miles
120,000 km
--
Do items in A and C.
80,000 miles
128,000 km
4 years
Do items in A, B, and E.
85,000 miles
136,000 km
--
Do item in A.
90,000 miles
144,000 km
--
Do items in A, B, C, D, and H.
95,000 miles
152,000 km
--
Do item in A.
100,000 miles
160,000 km
5 years
Do items in A, B, and E.
105,000 miles
168,000 km
--
Do items in A and C.
110,000 miles
176,000 km
--
Do items in A, B, and G.
115,000 miles
184,000 km
--
Do item in A.
120,000 miles
192,000 km
6 years
Do items in A, B, C, D, E, F, H, and I.
--
--
6 years
Replace brake fluid (see
BRAKE SYSTEM BLEEDING
). Use Acura DOT 3 Brake Fluid.
125,000 miles
200,000 km
--
Do item in A.
130,000 miles
208,000 km
--
Do items in A and B.
135,000 miles
216,000 km
--
Do items in A and C.
140,000 miles
224,000 km
7 years
Do items in A, B, and E.
145,000 miles
232,000 km
--
Do item in A.
150,000 miles
240,000 km
--
Do items in A, B, C, D, and H.
155,000 miles
248,000 km
--
Do item in A.
160,000 miles
256,000 km
--
Inspect idle speed (see
IDLE SPEED INSPECTION
) every 160,000 miles (256,000 km). Idle speed: M/T 750 ± 50 rpm in neutral, A/T 800 ± 50 rpm in N or P position.
160,000 miles
256,000 km
8 years
Do items in A, B, and E.
--
--
9 years
Replace brake fluid (see
BRAKE SYSTEM BLEEDING
). Use Acura DOT 3 Brake Fluid.
Do the items in parts A, B, C, D, E, F, G, H, and I as required for the mileage/time interval listed.
MAINTENANCE SCHEDULE
Part
Maintenance Hems
A
Replace engine oil (see
ENGINE OIL REPLACEMENT
) every 5,000 miles (8,000 km).
Engine oil capacity without oil filter: 4.0 L (4.2 US qt).
B
Replace engine oil filter (see
ENGINE OIL FILTER REPLACEMENT
) every 10,000 miles (16,000 km) or 1 year.
Engine oil capacity with oil filter: 4.2 L (4.4 US qt).
Check front and rear brakes (see
BRAKE SYSTEM INSPECTION AND TEST
) every 10,000 miles (16,000 km) or 1 year.
Lubricate all hinges, locks, and latches every 10,000 miles (16,000 km) or 1 year.
Rotate tires, and check tire inflation and condition every 10,000 miles (16,000 km).
Follow the pattern shown in the Owner's Manual.
Inspect tie-rod ends, steering gearbox, and gearbox boots (see
STEERING LINKAGE AND GEARBOX INSPECTION
) every 10,000 miles (16,000 km) or 1 year.
Inspect suspension components (see
COMPONENT LOCATION INDEX
), every 10,000 miles (16,000 km) or 1 year.
Inspect driveshaft boots (see
DRIVESHAFT INSPECTION
) every 10,000 miles (16,000 km) or 1 year.
Check boots for cracks and boot bands for tightness.
C
Replace air cleaner element when driving in dusty conditions (see
AIR CLEANER REMOVAL/INSTALLATION
) every 15,000 miles (24,000 km), (independent of time).
D
Replace dust and pollen filter (see
DUST AND POLLEN FILTER REPLACEMENT
) every 30,000 miles (48,000 km) or 2 years.
Inspect drive belt (see
DRIVE BELT INSPECTION
) every 30,000 miles (48,000 km) or 2 years.
Look for cracks and damage, then check the position of the drive belt auto-tensioner indicator.
E
Check parking brake adjustment (see
PARKING BRAKE INSPECTION AND ADJUSTMENT
) every 20,000 miles (32,000 km) or 1 year.
Check the number of clicks 6 to 9 when parking brake lever is pulled with 196 N (20 kgf, 44 lbf) of force.
Inspect brake hoses and lines including VSA (see
BRAKE HOSE AND LINE INSPECTION
) every 20,000 miles (32,000 km) or 1 year.
Check the master cylinder and VSA modulator-control unit for damage and leakage.
Inspect all fluid levels, condition of fluids, and checks for leaks every 20,000 miles (32,000 km) or 1 year.
Inspect exhaust system* (see
EXHAUST PIPE AND MUFFLER REPLACEMENT
) every 20,000 miles (32,000 km) or 1 year.
Check catalytic converter heat shield, exhaust pipe, and muffler for damage, leaks, and tightness.
Inspect fuel lines and connections* (see
FUEL LINE INSPECTION
) every 20,000 miles (32,000 km) or 1 year.
Check for loose connections, cracks, and deterioration; retighten loose connections and replace damaged parts.
Check lights and controls every 20,000 miles (32,000 km) or 1 year.
Check function of interior lights (see
COMPONENT LOCATION INDEX
), exterior lights (see
COMPONENT LOCATION INDEX
), and position of the headlights (see
HEADLIGHT ADJUSTMENT
).
Inspect vehicle underbody every 20,000 miles (32,000 km) or 1 year.
Check the paint for damage, scratches, stone chipping, and dents.
NOTE:
According to state and federal regulations, failure to do the maintenance items marked with an asterisk (*) will not void the client's emissions warranties. However, Acura recommends that all maintenance services be done at the recommended intervals to ensure long-term reliability.
Use the Severe Conditions schedule if the vehicle is driven MAINLY in Canada or in any of the following conditions; if only OCCASIONALLY driven in these conditions, use the Normal Conditions schedule.
Severe Driving Conditions
Do the items in parts A, B, C, D, E, F, G, H, and I as required for the mileage/time interval listed.
MAINTENANCE SCHEDULE
Part
Maintenance Items
F
Replace manual transmission fluid (see
MANUAL TRANSMISSION
) every 60,000 miles (96,000 km) or 3 years.
Capacity: 2.0 L (2.1 US at); use Acura MTF.
G
Inspect the valve clearance (see
VALVE CLEARANCE ADJUSTMENT
) every 110,000 miles (176,000 km), otherwise adjust only if noisy.
Intake: 0.21-0.25 mm (0.008-0.010 in.). Exhaust: 0.25-0.29 mm (0.010-0.011 in.).
Replace spark plugs (see
SPARK PLUG INSPECTION
) every 110,000 miles (176,000 km).
Use IZFR6K11 (NGK) or SKJ20DR-M11 (DENSO).
H
Replace automatic transmission fluid (see
ATF REPLACEMENT
) at 60,000 miles (96,000 km) or 3 years, then every 30,000 miles (48,000 km) or 2 years.
Capacity: 2.9 L (3.1 US qt); use Acura ATF-Z1.
I
Replace engine coolant (see
COOLANT REPLACEMENT
) at 120,000 miles (192,000 km) or 10 years, then every 60,000 miles (96,000 km) or 5 years.
Capacity: M/T 5.4 L (1.43 US gal), A/T 5.3 L (1.40 US gal); use Acura Long Life Antifreeze/Coolant Type 2.
The maintenance minder is an important feature of the multi-information display. The Acura TSX's onboard computer (ECM/PCM) calculates the remaining engine oil life. The system also displays the code for other scheduled maintenance items needing service.
Fig. 3: Identifying Multi-Information Display
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 4: Identifying Oil Life At 80 Percent Displayed
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 5: Identifying Oil Life At 15 Percent Displayed
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 6: Identifying SERVICE DUE NOW Display
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 7: Identifying SERVICE PAST DUE Display
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 8: Identifying 10 MILES SERVICE PAST DUE Display
Courtesy of AMERICAN HONDA MOTOR CO., INC.
NOTE:
Fig. 9: Identifying Oil Life RESET Display
NOTE:
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 10: Identifying Oil Life At 100 Percent Displayed
Courtesy of AMERICAN HONDA MOTOR CO., INC.
If the message "SERVICE DUE NOW" does not appear more than 12 months after the display is reset, change the engine oil every year.
NOTE:
MAINTENANCE MAIN ITEMS CHART
Symbol
Maintenance Main Items
A
Replace engine oil (see
ENGINE OIL REPLACEMENT
).
Engine oil capacity without oil filter: 4.0 L (4.2 US qt).
B
Replace engine oil and oil filter (see
ENGINE OIL FILTER REPLACEMENT
).
Engine oil capacity with oil filter: 4.2 L (4.4 US qt).
Check front and rear brakes (see
BRAKE SYSTEM INSPECTION AND TEST
).
Check parking brake adjustment (see
PARKING BRAKE INSPECTION AND ADJUSTMENT
).
Check the number of clicks (6 to 9) when the parking brake lever is pulled with 196 N (20 kgf, 44 lbf) of force.
Inspect tie-rod ends, steering gearbox, and gearbox boots (see
STEERING LINKAGE AND GEARBOX INSPECTION
).
Inspect suspension components (see
COMPONENT LOCATION INDEX
).
Inspect driveshaft boots (see
DRIVESHAFT INSPECTION
).
Check boots for cracks and boot bands for tightness.
Inspect brake hoses and lines including VSA lines (see
BRAKE HOSE AND LINE INSPECTION
).
Check the master cylinder and VSA modulator-control unit for damage and leakage.
Inspect all fluid levels and condition of fluids.
Inspect exhaust system* (see
EXHAUST PIPE AND MUFFLER REPLACEMENT
).
Check catalytic converter heat shields, exhaust pipes, and muffler for damage, leaks, and tightness.
Inspect fuel lines and connections* (see
FUEL LINE INSPECTION
).
Check for loose connections, cracks, and deterioration; retighten loose connections and replace damaged parts.
NOTE:
According to state and federal regulations, failure to do the maintenance items marked with an asterisk (*) will not void the client's emissions warranties. However, Acura recommends that all maintenance services be done at the recommended interval, to ensure long-term reliability.
MAINTENANCE SUB ITEMS
Number
Maintenance Sub Items
1
Rotate tires, and check tire inflation and condition.
Follow the pattern shown in the Owner's Manual.
2
Replace air cleaner element (see
AIR CLEANER REMOVAL/INSTALLATION
).
If the vehicle is driven primarily in dusty conditions, replace every 15,000 miles (24,000 km).
Replace dust and pollen filter (see
DUST AND POLLEN FILTER REPLACEMENT
).
Inspect drive belt (see
DRIVE BELT INSPECTION
).
Look for cracks and damage, then check the position of the drive belt auto-tensioner indicator.
3
Replace manual transmission fluid (see
MANUAL TRANSMISSION
).
Capacity: 2.0 L (2.1 US qt); use Acura MTF.
Replace automatic transmission fluid (see
ATF REPLACEMENT
).
4
Replace spark plugs (see
SPARK PLUG INSPECTION
).
Use IZFR6K11 (NGK) or SKJ20DR-M11 (DENSO).
Inspect valve clearance (cold) (see
VALVE CLEARANCE ADJUSTMENT
).
Intake: 0.21-0.25 mm (0.008-0.010 in.). Exhaust: 0.25-0.29 mm (0.010-0.011 in.).
5
Replace engine coolant (see
COOLANT REPLACEMENT
).
Capacity (including the reservoir): M/T model 5.4 L (1.43 US gal), A/T model 5.3 L (1.40 US gal), use Acura Long Life Antifreeze/Coolant Type 2.