elsawin online

DATACENTER ERROR!!! Внимание! Авария в датацентре!!

Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru

Attention! Please use superetka.com/elsa

E-Golf

Please use
superetka.com/elsa

1: Overview of control units
2: Control unit 1 for information electronics J794
3: Front passenger door control unit J387
4: Engine sound generator control unit J943
5: Climatronic control unit J255
6: Display unit for front information display and operating unit control unit J685
7: Main beam assist control unit J844
8: Front camera for driver assist systems R242
9: Selector lever E313
10: Steering column electronics control unit J527
11: Storage compartment with interface for mobile telephone R265
12: Multifunction steering wheel control unit J453
13: Driver door control unit J386
14: Control unit for electronic steering column lock J764
15: Control unit in dash panel insert J285
16: Onboard supply control unit J519
17: Parking aid control unit J446 / park assist steering control unit J791
18: Emergency call module control unit and communication unit J949
19: Data bus diagnostic interface J533
20: Airbag control unit J234
21: Control unit for cornering light and headlight range control J745
22: Module monitor control unit for batteries J497
23: Battery regulation control unit J840
24: Fresh air blower control unit J126
25: Interface for entry and start system J965

elsa
elsa on kolhosniki not support now!

e-Golf	Fitting Locations	No. 805 / 1

		Edition 04.2014

Control units in middle part of vehicle

Overview of control units

1 -	Control unit 1 for information electronics -J794-

q	Fitting location → Chapter

2 -

3 -	Front passenger door control unit -J387-

q	Fitting location → Chapter

4 -	Engine sound generator control unit -J943-

q	Fitting location → Chapter

5 -	Climatronic control unit -J255-

q	Fitting location → Chapter

6 -	Display unit for front information display and operating unit control unit -J685-

q	Fitting location → Chapter

7 -	Main beam assist control unit -J844-

q	Fitting location → Chapter

8 -	Front camera for driver assist systems -R242-

q	Fitting location → Chapter

9 -	Selector lever -E313-

q	Fitting location → Chapter

10 -	Steering column electronics control unit -J527-

q	Fitting location → Chapter

11 -	Storage compartment with interface for mobile telephone -R265-

q	Fitting location → Chapter

12 -	Multifunction steering wheel control unit -J453-

q	Fitting location → Chapter

13 -	Driver door control unit -J386-

q	Fitting location → Chapter

14 -	Control unit for electronic steering column lock -J764-

q	Fitting location → Chapter

15 -	Control unit in dash panel insert -J285-

q	Fitting location → Chapter

16 -	Onboard supply control unit -J519-

q	Fitting location → Chapter

17 -	Park assist steering control unit -J791- , parking aid control unit -J446-

q	Fitting location left-hand drive → Chapter

q	Fitting location right-hand drive → Chapter

18 -	Emergency call module control unit and communication unit -J949-

q	Fitting location → Chapter

19 -	Data bus diagnostic interface -J533-

q	Fitting location → Chapter

20 -	Airbag control unit -J234-

q	Fitting location → Chapter

21 -	Control unit for cornering light and headlight range control -J745-

q	Fitting location → Chapter

22 -	Module monitor control unit for batteries -J497-

q	Fitting location → Chapter

23 -	Battery regulation control unit -J840-

q	Fitting location → Chapter

24 -	Fresh air blower control unit -J126-

q	Fitting location → Chapter

25 -	Interface for entry and start system -J965-

q	Fitting location left-hand drive → Chapter

q	Fitting location right-hand drive → Chapter

Control unit 1 for information electronics -J794-

Fitting location:

In glove compartment

Note

Multiway connector housing J (chambers: 9-18), made up of connectors K, L, M and N.

1 -	Control unit 1 for information electronics -J794-

A -	2-pin connector

q	Digital radio aerial -R183-

B -	2-pin connector

q	GSM aerial -R205-

C -

Vacant

D -	2-pin connector

q	GPS aerial -R50-

E -	4-pin connector

q	Radio aerial 2 -R93-

F -	4-pin connector

q	Radio aerial -R248-

G -

Vacant

H -	5-pin connector -T5ae-

q	Interface for external multimedia units -R215-¹⁾

q	Connection for external audio sources -R199-¹⁾

q	USB hub -R293-¹⁾

¹⁾ Depending on equipment

I -	5-pin connector -T5ah-

q	Display unit for front information display and operating unit control unit -J685-

J -	8-pin connector -T8aq-

K -	12-pin connector -T12ag-

L -	12-pin connector -T12a-

M -	12-pin connector -T12al-

N -	8-pin connector -T8ar-

O -

Vacant

Back to overview → Chapter

Connector assignment of control unit 1 for information electronics -J794-

-T8ar- (N)	Designation	-T8aq- (J)	Designation	-T2n- (O)	Designation
1	Rear right treble loudspeaker -R16- , + rear right bass loudspeaker -R17- , +	9		1
2	Front right treble loudspeaker -R22- , + front right bass loudspeaker -R23- , +	10		2
3	Front left treble loudspeaker -R20- , + front left bass loudspeaker -R21- ,+	11
4	Rear left treble loudspeaker -R14- , + rear left bass loudspeaker -R15- , +	12
5	Rear right treble loudspeaker -R16- , - rear right bass loudspeaker -R17- , -	13
6	Front right treble loudspeaker -R22- , - front right bass loudspeaker -R23- , -	14
7	Front left treble loudspeaker -R20- , - front left bass loudspeaker -R21- ,-	17(1)	Terminal 31
8	Rear left treble loudspeaker -R14- , - rear left bass loudspeaker -R15- , -	18(2)	Terminal 30

-T12al- (M)	Designation	-T12ag- (K)	Designation	-T12a- (L)	Designation
1	B415 Connection 1 (infotainment CAN bus, high), in main wiring harness	1	Interface for external multimedia units -R215-¹ Connection for external audio sources -R199-¹	1	Telephone microphone -R38-
2	Display unit for front information display and operating unit control unit -J685-	2	Interface for external multimedia units -R215-¹ Connection for external audio sources -R199-¹	2
3		3	Interface for external multimedia units -R215-¹ Connection for external audio sources -R199-¹ USB hub -R293-¹	3
4		4	Interface for external multimedia units -R215-¹ Connection for external audio sources -R199-¹	4
5	Terminal 30	5	Interface for external multimedia units -R215-¹	5
6	A178 Connection (infotainment CAN bus, high), in dash panel wiring harness	6	Interface for external multimedia units -R215-¹	6	Reversing camera -R189-
7	B421 Connection 1 (infotainment CAN bus, low), in main wiring harness	7	Interface for external multimedia units -R215-¹ Connection for external audio sources -R199-¹	7	Telephone microphone -R38- , shielding connection
8	Display unit for front information display and operating unit control unit -J685-	8	Interface for external multimedia units -R215-¹ Connection for external audio sources -R199-¹	8
9		9	Interface for external multimedia units -R215-¹	9
10		10	Interface for external multimedia units -R215-¹	10
11		11	Interface for external multimedia units -R215-¹	11
12	A179 Connection (infotainment CAN bus, low), in dash panel wiring harness	12	Interface for external multimedia units -R215-¹	12	Reversing camera -R189-

¹⁾ Depending on equipment

Back to overview → Chapter

Front passenger door control unit -J387-

Fitting location:

In front passenger door.

1 -	Front passenger door control unit -J387-

A -	6-pin connector -T6f-

B -	20-pin connector -T20b-

C -	16-pin connector -T16g-

D -	32-pin connector -T32c-

Back to overview → Chapter

Connector assignment of front passenger door control unit -J387-

-T6f- (A)

Designation

-T20b- (B)

Designation

-T16g- (C)

Designation

-T32c- (D)

Designation

Front passenger side entry light in exterior mirror -W53-

Right window regulator motor -V15-

Front passenger side exterior mirror -VX5-

Light for passenger door ambient lighting -W87-

Front passenger side exterior mirror -VX5-

Terminal 58

Front passenger door contact switch -F3-

Front passenger side exterior mirror -VX5-

Terminal 31

Right window regulator motor -V15-

Front passenger door central locking actuator for SAFELOCK function -F244-

Front passenger side mirror adjustment motor -V25-

Front passenger side mirror adjustment motor -V150-

Light for passenger door ambient lighting -W87-

Front passenger side fold-in mirror motor -V122-

Rear right window regulator motor -V27-

LIN bus

Front passenger side fold-in mirror motor -V122-

Front passenger door lock unit -VX22-

Front passenger side turn signal repeater bulb -L132-

Central locking SAFE function motor, in front passenger door -V162-

Front passenger door central locking motor -V57-

Front passenger side exterior mirror -VX5-

Central locking button -E600-

B407 Connection 2 (convenience CAN bus, low), in main wiring harness

Front passenger side exterior mirror -VX5-

B398 Connection 2 (convenience CAN bus, high), in main wiring harness

Heated exterior mirror on front passenger side -Z5-

Front passenger side exterior mirror -VX5-

Light conductor for front right sill panel moulding ambient lighting -W68-

Terminal 30

Terminal 31

Front passenger side window regulator button -E716-

Back to overview → Chapter

Engine sound generator control unit -J943-

Fitting location:

behind Climatronic control unit -J255-

1 -	Engine sound generator control unit -J943-

A -	12-pin connector -T12ab-

Back to overview → Chapter

Connector assignment of engine sound generator control unit -J943-

-T12ab- (A)	Designation
1	Terminal 30
2	Terminal 31
3	Actuator 1 for engine sound generator -R257-
4	Actuator 1 for engine sound generator -R257-
5
6
7	Terminal 30
8	Terminal 31
9
10
11	B390 Connection 1 (powertrain CAN bus, low), in main wiring harness
12	B383 Connection 1 (powertrain CAN bus, high), in main wiring harness

Back to overview → Chapter

Climatronic control unit -J255-

Fitting location:

In centre of dash panel.

1 -	Climatronic control unit -J255-

A -	16-pin connector -T16d-

B -	16-pin connector -T16c-

C -	20-pin connector -T20c-

Back to overview → Chapter

Connector assignment of Climatronic control unit -J255-

-T16d- (A)

Designation

-T16c- (B)

Designation

-T20c- (C)

Designation

Left temperature flap control motor -V158-

Potentiometer for front air distribution flap control motor -G642-
Potentiometer for fresh air/recirculated air, air flow flap control motor -G644-
Potentiometer for defroster flap control motor -G135-
Potentiometer for left temperature flap control motor -G220-
Potentiometer for right temperature flap control motor -G221-

Sunlight penetration photosensor -G107-

Left temperature flap control motor -V158-

Potentiometer for left temperature flap control motor -G220-

Defroster flap control motor -V107-

Potentiometer for right temperature flap control motor -G221- ,

Sunlight penetration photosensor -G107-

Defroster flap control motor -V107-

Potentiometer for defroster flap control motor -G135-

Front air distribution flap control motor -V426-

Potentiometer for front air distribution flap control motor -G642-

B506 Connection (convenience CAN bus, high), in interior wiring harness

Front air distribution flap control motor -V426-

B507 Connection (convenience CAN bus, low), in interior wiring harness

Potentiometer for fresh air/recirculated air, air flow flap control motor -G644-

Footwell vent temperature sender -G192-

Fresh air/recirculated air, air flow flap control motor -V425-

Sunlight penetration photosensor -G107-

Fresh air/recirculated air, air flow flap control motor -V425-

Right temperature flap control motor -V159-

Evaporator temperature sensor -G308-

Right temperature flap control motor -V159-

Left vent temperature sender -G150-

t	Terminal 31

Right vent temperature sender -G151-

A209 Connection 1 (LIN bus) in dash panel wiring harness

Sunlight penetration photosensor -G107-
Right vent temperature sender -G151-
Left vent temperature sender -G150-

t	Terminal 31

Air conditioning system relay -J32-

Terminal 31

Terminal 30

Back to overview → Chapter

Display unit for front information display and operating unit control unit -J685-

Fitting location:

In the centre console.

1 -	Display unit for front information display and operating unit control unit -J685-

A -	12-pin connector -T12ai-

B -	5-pin connector -T5ad-

q	Control unit 1 for information electronics -J794-

Back to overview → Chapter

Connector assignment of display unit for front information display and operating unit control unit -J685-

-T12ai- (A)	Designation
1	Terminal 30
2
3	B415 Connection 1 (infotainment CAN bus, high), in main wiring harness
4
5	Control unit 1 for information electronics -J794-
6
7	Terminal 31
8
9	B421 Connection 1 (infotainment CAN bus, low), in main wiring harness
10
11	Control unit 1 for information electronics -J794-
12

Back to overview → Chapter

Main beam assist control unit -J844-

Fitting location:

On interior mirror.

1 -	Main beam assist control unit -J844-

A -	8-pin connector -T8bg-

Back to overview → Chapter

Connector assignment of main beam assist control unit -J844-

-T8bg- (A)	Designation
1	Terminal 15
2	Terminal 31
3	B108 Connection 1 (CAN bus extended, high), in main wiring harness
4
5
6	Front interior light -WX1- , -
7
8	B109 Connection 1 (CAN bus extended, low), in main wiring harness

Back to overview → Chapter

Front camera for driver assist systems -R242-

Fitting location:

Near interior mirror.

1 -	Front camera for driver assist systems -R242-

A -	12-pin connector -T12ar-

Back to overview → Chapter

Connector assignment of front camera for driver assist systems -R242-

-T12ar- (A)	Designation
1	Adaptive cruise control unit -J428-
2	B109 Connection 1 (CAN bus extended, low), in main wiring harness
3
4	Windscreen heater for front sensors -Z113-
5	Terminal 31
6	Terminal 15
7	Adaptive cruise control unit -J428-
8	B108 Connection 1 (CAN bus extended, high), in main wiring harness
9
10
11
12

Back to overview → Chapter

Selector lever -E313-

Fitting location:

In centre console, on selector lever bracket.

1 -	Selector lever -E313-

A -	10-pin connector -T10s-

B -	10-pin connector -T10t-

q	Adapter wire for selector lever position display -Y26-

Back to overview → Chapter

Connector assignment of selector lever -E313-

-T10s- (A)	Designation	-T10t- (A)	Designation
1	Terminal 31	1	Selector lever position display -Y26-
2	Steering column electronics control unit -J527-	2	Selector lever position display -Y26-
3		3	Selector lever position display -Y26-
4		4	Selector lever position display -Y26-
5	Terminal 58	5	Selector lever position display -Y26-
6		6	Selector lever position display -Y26-
7	B776 Connection 1 (hybrid CAN bus, high), in main wiring harness	7	Selector lever position display -Y26-
8	B777 Connection 1 (hybrid CAN bus, low), in main wiring harness	8	Selector lever position display -Y26-
9	Terminal 15	9	Selector lever position display -Y26-
10	Terminal 30	10	Selector lever position display -Y26-

Back to overview → Chapter

Steering column electronics control unit -J527-

Fitting location:

On A-pillar.

1 -	Steering column electronics control unit -J527-

A -	16-pin connector -T16r-

B -	4-pin connector -T4k-

Back to overview → Chapter

Connector assignment of steering column electronics control unit -J527-

-T16r- (A)

Designation

-T16r- (A)

Designation

-T4k- (B)

Designation

Terminal 30

Driver side airbag igniter -N95-

Terminal 31

Driver side airbag igniter -N95-

B507 Connection (convenience CAN bus, low), in interior wiring harness

Selector lever -E313-

B506 Connection (convenience CAN bus, high), in interior wiring harness

Engine control unit -J623-

t	Cruise control system

Engine control unit -J623-

t	Terminal 50

Onboard supply control unit -J519-

t	Terminal 15

Onboard supply control unit -J519-

t	Terminal S

B549 Connection 2 (LIN bus) in main wiring harness

Onboard supply control unit -J519-

t	Terminal 15

Back to overview → Chapter

Storage compartment with interface for mobile telephone -R265-

Fitting location:

Under centre armrest, front.

1 -	Storage compartment with interface for mobile telephone -R265-

A -	4-pin connector -T4h-

B -	2-pin connector

q	Two-way signal amplifier for mobile telephone/data services -J984-

q	GSM aerial

Back to overview → Chapter

Connector assignment for storage compartment with interface for mobile telephone -R265-

-T4h- (A)	Designation
1	Terminal 30
2	Terminal 30
3	Control unit 1 for information electronics -J794-
4	Terminal 31

Back to overview → Chapter

Multifunction steering wheel control unit -J453-

Fitting location:

Inside the operating unit of the multifunction buttons on left of steering wheel -E440- .

1 -	Multifunction steering wheel control unit -J453-

A -	5-pin connector -T5k-

B -	12-pin connector -T12k-

Back to overview → Chapter

Connector assignment of multifunction steering wheel control unit -J453-

-T5k- (A)

Designation

-T12k- (B)

Designation

Terminal 31

Steering column electronics control unit -J527-

t	Terminal 30

Steering column electronics control unit -J527-

LIN bus

Driver side airbag igniter -N95-

Steering column electronics control unit -J527-

Terminal 31

Horn plate -H-

Multifunction steering wheel control unit -J453-

LIN bus

Multifunction steering wheel control unit -J453-

t	Terminal 30

Multifunction steering wheel control unit -J453-

Back to overview → Chapter

Driver door control unit -J386-

Fitting location:

In driver door.

1 -	Driver door control unit -J386-

A -	6-pin connector -T6o-

B -	20-pin connector -T20a-

C -	16-pin connector -T16a-

D -	32-pin connector -T32a-

Back to overview → Chapter

Connector assignment of driver door control unit -J386-

-T6o- (A)	Designation	-T20a- (B)	Designation	-T16a- (C)	Designation	-T32a- (D)	Designation
1		1	Driver side contact switch in lock cylinder -F241-	1	Driver side entry light in exterior mirror -W52-	1	Central locking SAFE function warning lamp -K133-
2		2		2		2
3	Left window regulator motor -V14-	3		3	Driver side exterior mirror -VX4-	3	Light for driver door ambient lighting -W86-
4		4		4	Driver side exterior mirror -VX4-	4	Terminal 58
5		5	Driver door contact switch -F2-	5	Driver side mirror adjustment motor -V17- Driver side mirror adjustment motor -V149-	5	Terminal 31
6	Left window regulator motor -V14-	6	Driver door central locking actuator for SAFELOCK function -F243-	6		6
		7		7	Driver side mirror adjustment motor -V17-	7
		8		8	Driver side mirror adjustment motor -V149-	8	Light for driver door ambient lighting -W86-
		9		9	Driver side fold-in mirror motor -V121-	9
		10	Rear left window regulator motor -V26-	10	Driver side fold-in mirror motor -V121-	10
		11	Driver door lock unit -VX21-	11	Driver side turn signal repeater bulb in exterior mirror -L131-	11
		12	Driver door central locking SAFELOCK function motor -V161-	12		12	Warning light for activated childproof lock -K236-
		13	Driver door central locking motor -V56-	13	Driver side exterior mirror -VX4-	13	Driver side interior locking button for central locking system -E308-
		14	B507 Connection (convenience CAN bus, low), in interior wiring harness	14	Driver side exterior mirror -VX4-	14
		15	B506 Connection (convenience CAN bus, high), in interior wiring harness	15	Heated exterior mirror on driver side -Z4-	15
		16		16	Driver side exterior mirror -VX4-	16	Light conductor for front left sill panel moulding ambient lighting -W67-
		17				17
		18				18
		19	Terminal 30			19
		20	Terminal 31			20
						21
						22
						23
						24	Mirror adjustment switch -E43- Mirror adjustment changeover switch -E48-
						25	Fold-in mirror switch -E263-
						26
						27	Childproof lock button -E318-
						28	Driver side interior locking button for central locking system -E308-
						29	Rear passenger side window regulator button -E713-
						30	Rear driver side window regulator button -E711-
						31	Front passenger side window regulator button -E716-
						32	Front driver side window regulator button -E710-

Back to overview → Chapter

Control unit for electronic steering column lock -J764-

Fitting location:

On A-pillar.

1 -	Control unit for electronic steering column lock -J764-

A -	16-pin connector -T16s-

Back to overview → Chapter

Connector assignment of control unit for electronic steering column lock -J764-

-T16s- (A)

Designation

-T16s- (A)

Designation

Terminal 30

Terminal 31

Starter button -E378-

Engine control unit -J623-

t	Terminal 50

Starter button -E378-

Onboard supply control unit -J519-

t	Terminal 15

Onboard supply control unit -J519-

t	Terminal S

B507 Connection (convenience CAN bus, low), in interior wiring harness

Onboard supply control unit -J519-

t	Terminal 15

B506 Connection (convenience CAN bus, high), in interior wiring harness

Back to overview → Chapter

Control unit in dash panel insert -J285-

Fitting location:

In dash panel.

1 -	Control unit in dash panel insert -J285-

A -	18-pin connector -T18-

Back to overview → Chapter

Connector assignment of control unit in dash panel insert -J285-

-T18- (A)	Designation	-T18- (A)	Designation
1	Terminal 30	10	Terminal 31
2		11
3		12
4		13
5		14
6		15
7		16
8	Immobiliser reader coil -D2-	17	B507 Connection (convenience CAN bus, low), in interior wiring harness
9	Immobiliser reader coil -D2-	18	B506 Connection (convenience CAN bus, high), in interior wiring harness

Back to overview → Chapter

Onboard supply control unit -J519-

Fitting location:

Behind dash panel, left

1 -	Onboard supply control unit -J519-

A -	73-pin connector -T73a-

B -	46-pin connector -T46b-

C -	73-pin connector -T73c-

Back to overview → Chapter

Connector assignment of onboard supply control unit -J519-

-T73a- (A)

Designation

-T46b- (B)

Designation

-T73c- (C)

Designation

Terminal 30

Right headlight dipped beam bulb -M31-

Terminal 30

t	left light supply

Heated seat cushion for driver seat -Z6-

Right headlight main beam bulb -M32-

Bulb 2 for rear right turn signal -M81-

Left LED module for daytime running light and side light -L176-

Terminal 30

t	anti-theft alarm system

Heated seat cushion for front passenger seat -Z8-

Right LED module for daytime running light and side light -L177-

Left headlight dipped beam bulb -M29-

Rear right door central locking motor, lock -V215-

Terminal 58

Rear right door central locking motor, lock -V215-

Washer pump -V5-

Right brake and tail light bulb -M22-

Rear lid central locking motor -V53-

Bulb 2 for rear left turn signal -M80-

Left side light bulb -M1-

Left brake and tail light bulb 2 -M58-

Left reversing light bulb -M16-

Term. 31

Front right brake pad wear sender -G35-

A29 Connection (interior light) in dash panel wiring harness

Terminal 15 voltage supply relay -J329-

Brake fluid level warning contact -F34-

Terminal 15

Bonnet contact switch -F387-

Entry and start authorisation control unit -J518-

Rotary light switch -EX1-

t	Dipped beam position

B506 Connection (convenience CAN bus, high), in interior wiring harness

Coolant shortage indicator sender -G32-

Rotary light switch -EX1-

t	Automatic headlight control position

B507 Connection (convenience CAN bus, low), in interior wiring harness

Ambient temperature sensor -G17- , -
coolant shortage indicator sender -G32- , -
windscreen washer fluid level sender -G33- , -

Headlight range control and instrument illumination regulator -EX14-¹⁾

Front right turn signal bulb -M7-

Right side light bulb -M3-

Front right headlight -MX2-

Front left headlight -MX1-

Horn relay -J413-

Heated rear window relay -J9-

Ambient temperature sensor -G17-

Windscreen washer fluid level sender -G33-

Rain and light sensor -G397-

Rotary light switch -EX1-

Wiper motor control unit -J400-

Alarm horn -H12-

Rear right turn signal bulb -M8-

Rear lid handle release button -E234-

Right LED module for daytime running light and side light -L177-

Button for deactivating interior monitoring and vehicle inclination sensor -E616-

Rear right door central locking actuator for SAFELOCK function -F246-

Rear left door central locking actuator for SAFELOCK function -F245-

Rear left door central locking motor, lock -V214-

Front left turn signal bulb -M5-

Rear right door central locking motor, lock -V215-

Left headlight main beam bulb -M30-

Alarm horn -H12-

Front right seat temperature sender -G345-

Hazard warning light switch -EX3-

Rotary light switch -EX1-

Front left seat temperature sender -G344-

Ignition/starter switch -D-

t	Terminal 15

Left LED module for daytime running light and side light -L176-

Rotary light switch -EX1-

t	Zero position

Ignition/starter switch -D-

t	Terminal 15

Rear right door contact switch -F11-

Hazard warning light switch -EX3-

Rear left door contact switch -F10-

Button for deactivating interior monitoring and vehicle inclination sensor -E616-

Rear lid lock unit -F256-

Terminal 31

Ignition/starter switch -D-

t	Terminal S

Headlight range control and instrument illumination regulator -EX14-¹⁾

Terminal 31

t	heated seats

Additional brake light bulb -M25-

Headlight range control and instrument illumination regulator -EX14-¹⁾

Left number plate light -X4-
Right number plate light -X5-

Rear left turn signal bulb -M6-

Rear window wiper motor -V12-

Terminal 58d

Terminal 31

W71 Connection (reversing light) in rear wiring harness

Right brake and tail light bulb 2 -M59-

Terminal 30

t	right light supply

Front interior light -WX1-

Rear left door central locking motor, lock -V214-

Left brake and tail light bulb -M21-

Rear left fog light bulb -L46-
Rear right fog light bulb -L47-

Front left footwell light -K268-
Front right footwell light -K269-

Terminal 30

t	central locking supply

Terminal 30

¹⁾ Depending on equipment

Back to overview → Chapter

Parking aid control unit -J446- / park assist steering control unit -J791-

Parking aid control unit -J446- / park assist steering control unit -J791- , left-hand drive models

Fitting location:

Behind dash panel on driver side.

1 -	Parking aid control unit -J446- / park assist steering control unit -J791-

A -	18-pin connector -T18k-

B -	26-pin connector -T26i-

Back to overview → Chapter

Connector assignment of parking aid control unit -J446- / park assist steering control unit -J791- , left-hand drive models

-T18k- (A)

Designation

-T26i- (B)

Designation

Front left sender for park assist steering on left side of vehicle -G568-²⁾

Signal

Front parking aid warning buzzer -H22-¹⁾

Front centre left parking aid sender -G254-

Signal

Park assist steering button -E581-

Front right parking aid sender -G252-

Signal

Warning light for park assist steering -K241-

Rear left parking aid sender -G203-

Signal

Rear centre right parking aid sender -G205-

Signal

Rear right park assist steering sender -G717-

Signal

Rear parking aid warning buzzer -H15-¹⁾

Front right parking aid sender -G252-
Front centre right parking aid sender -G253-
Front centre left parking aid sender -G254-
Front left parking aid sender -G255-
Front left sender for park assist steering on left side of vehicle -G568-²⁾
Front right sender for park assist steering on right side of vehicle -G569-²⁾

t	Terminal 31

Front parking aid warning buzzer -H22-¹⁾

Front left parking aid sender -G255-

Signal

Front centre right parking aid sender -G253-

Signal

Front right sender for park assist steering on right side of vehicle -G569-²⁾

Signal

Terminal 31

t	Terminal 15

Terminal 15

Rear parking aid warning buzzer -H15-¹⁾

Parking aid button -E266-

Parking aid warning lamp -K136-

Rear left parking aid sender -G203-
Rear centre left parking aid sender -G204-
Rear centre right parking aid sender -G205-

Rear right parking aid sender -G206-
Rear left park assist steering sender -G716-²⁾
Rear right park assist steering sender -G717-²⁾

t	Terminal 15

Rear left park assist steering sender -G716-²⁾

Signal

Rear centre left parking aid sender -G204-

Signal

Rear right parking aid sender -G206-

Signal

t	Terminal 31

B664 Connection (CAN bus running gear sensors, low), in main wiring harness

B663 Connection (CAN bus running gear sensors, high), in main wiring harness

¹⁾ Only models with park assist steering

²⁾ Depending on equipment

Back to overview → Chapter

Parking aid control unit -J446- / park assist steering control unit -J791- , right-hand drive models

Fitting location:

Behind dash panel on driver side.

1 -	Parking aid control unit -J446- / park assist steering control unit -J791-

A -	26-pin connector -T26i-

q	Connector assignment identical to LHD → Anchor

B -	18-pin connector -T18k-

q	Connector assignment identical to LHD → Anchor

Back to overview → Chapter

Emergency call module control unit and communication unit -J949-

Fitting location:

behind dash panel insert -KX2-

1 -	Emergency call module control unit and communication unit -J949-

A -	26-pin connector -T26a-

B -	1) Emergency call module aerial -R263-

B -	2) GSM aerial -R205-

Back to overview → Chapter

Connector assignment of data bus diagnostic interface -J533-

-T26a- (A)	Designation	-T26a- (A)	Designation
1	Terminal 30	14	B506 Connection (convenience CAN bus, high), in interior wiring harness
2	B507 Connection (convenience CAN bus, low), in interior wiring harness	15
3		16
4	Telephone microphone -R38-	17	Telephone microphone -R38-
5	Telephone microphone -R38-	18	Telephone microphone -R38-
6	Telematics button module -E734-	19	Telematics button module -E734-
7	Telematics button module -E734-	20	Telematics button module -E734-
8		21
9		22
10	Control unit 1 for information electronics -J794-	23
11	Control unit 1 for information electronics -J794-	24
12		25
13		26	Terminal 31

Back to overview → Chapter

Data bus diagnostic interface -J533-

Fitting location:

Below the dash panel.

1 -	Data bus diagnostic interface -J533-

A -	20-pin connector -T20-

Back to overview → Chapter

Connector assignment of data bus diagnostic interface -J533-

-T20- (A)	Designation	-T20- (A)	Designation
1	Terminal 30	11	Terminal 31
2	Terminal 30	12	Terminal 31
3	A227 Connection 2 (LIN bus) in dash panel wiring harness	13	B549 Connection 2 (LIN bus) in main wiring harness
4		14	Terminal 15
5	B407 Connection 2 (convenience CAN bus, low), in main wiring harness	15	B398 Connection 2 (convenience CAN bus, high), in main wiring harness
6	B390 Connection 1 (powertrain CAN bus, low), in main wiring harness	16	B383 Connection 1 (powertrain CAN bus, high), in main wiring harness
7	B109 Connection 1 (CAN bus extended, low), in main wiring harness	17	B108 Connection 1 (CAN bus extended, high), in main wiring harness
8	B664 Connection (CAN bus running gear sensors, low), in main wiring harness	18	B663 Connection (CAN bus running gear sensors, high), in main wiring harness
9	B714 Connection 1 (CAN bus diagnosis, low), in main wiring harness	19	B713 Connection 1 (CAN bus diagnosis, high), in main wiring harness
10	A179 Connection (infotainment CAN bus, low), in dash panel wiring harness	20	A178 Connection (infotainment CAN bus, high), in dash panel wiring harness

Back to overview → Chapter

Airbag control unit -J234-

Fitting location:

Behind centre console.

1 -	Airbag control unit -J234-

A -	90-pin connector -T90-

Back to overview → Chapter

Connector assignment of airbag control unit -J234-

-T90- (A)

Designation

-T90-

Designation

Key operated switch to deactivate front passenger side airbag -E224-

Driver side knee airbag igniter -N295-

Seat occupied sensor, front passenger side -G128-

Driver side knee airbag igniter -N295-

Front passenger front airbag deactivated warning lamp -K145-

Rear side airbag igniter on driver side -N201-

Front passenger side belt switch, seat row 2 -F392-

Rear side airbag igniter on driver side -N201-

Front passenger front airbag deactivated warning lamp -K145-

Rear belt tensioner igniter on driver side -N196-

Driver side belt switch, seat row 2 -F390-

Rear belt tensioner igniter on driver side -N196-

Driver side curtain airbag igniter -N251-

Belt switch for seat row 2, middle -F391-

Driver side curtain airbag igniter -N251-

Driver side airbag igniter -N95-

Driver seat belt tensioner igniter 1 -N153-

Side airbag igniter on driver side -N199-

Front passenger front airbag deactivated warning lamp -K145-

t	Terminal 30

Battery regulation control unit -J840-

B710 Connection 5 (LIN bus) in main wiring harness

Battery regulation control unit -J840-

Driver side belt switch -E24-
Rear side airbag igniter on front passenger side -N202-
Rear side airbag igniter on driver side -N201-
Side airbag igniter on driver side -N199-
Side airbag igniter on front passenger side -N200-
Seat occupied sensor, front passenger side -G128-
Front passenger side belt switch -E25-
Front passenger side belt switch, seat row 2 -F392-
Driver side belt switch, seat row 2 -F390-
Belt switch, seat row 2, middle -F391-
Front passenger side airbag igniter 1 -N131-
Key operated switch to deactivate front passenger side airbag -E224-

t	Terminal 31

Rear side airbag igniter on front passenger side -N202-

Rear belt tensioner igniter on front passenger side -N197-

Front passenger side curtain airbag igniter -N252-

Front passenger side airbag igniter 1 -N131-

Front passenger seat belt tensioner 1 igniter -N154-

Crash sensor for front airbag -G190-

Front passenger seat belt tensioner 1 igniter -N154-

Crash sensor for front airbag -G190-

Side airbag igniter on front passenger side -N200-

Terminal 30

Key operated switch to deactivate front passenger side airbag -E224-

Front passenger side belt switch -E25-

Driver side belt switch -E24-

Rear side airbag crash sensor on driver side -G256-

Side airbag crash sensor on driver side -G179-

Diagnostic connection -U31-

Rear side airbag crash sensor on front passenger side -G257-

Side airbag crash sensor on front passenger side -G180-

B383 Connection 1 (powertrain CAN bus, high), in main wiring harness

B390 Connection 1 (powertrain CAN bus, low), in main wiring harness

Back to overview → Chapter

Control unit for cornering light and headlight range control -J745-

Fitting location:

Behind dash panel on driver side.

1 -	Control unit for cornering light and headlight range control -J745-

A -	26-pin connector -T26h-

Back to overview → Chapter

Connector assignment of control unit for cornering light and headlight range control -J745-

-T26h- (A)	Designation	-T26h- (A)	Designation
1		14
2	B668 Connection 2 (CAN bus extended high), in main wiring harness	15	Right headlight range control motor -V49-
3	B669 Connection 2 (CAN bus extended low), in main wiring harness	16	Left headlight range control motor -V48-
4		17	Left headlight range control motor -V48-
5		18	Left headlight range control motor -V48-
6		19	Left headlight range control motor -V48-
7		20	Right headlight range control motor -V49-
8		21	Right headlight range control motor -V49-
9		22	Right headlight range control motor -V49-
10		23	Terminal 15
11		24	Terminal 31
12		25
13		26

Back to overview → Chapter

Module monitor control unit for batteries -J497-

Fitting location:

in hybrid battery unit -AX1-

1 -	Module monitor control unit for batteries -J497-

A -	4-pin connector -T4bx-

B -	18-pin connector -T18c-

C -	12-pin connector -T12j-

D -	12-pin connector -T12i-

Back to overview → Chapter

Connector assignment of module monitor control unit for batteries -J497-

-T4bx- (A)	Designation	-T18c- (B)	Designation	-T12j- (C)	Designation	-T12i- (D)	Designation
1	Terminal 31	1	Terminal 30	1	High-voltage battery pre-charging contactor -J1044-	1 (1A)	High-voltage battery power contactor 2 -J1058-
2		2	Terminal 30	2	High-voltage battery power contactor 1 -J1057-	2 (2A)	High-voltage battery power contactor 2 -J1058-
3		3		3	High-voltage battery power contactor 2 -J1058-	3 (3A)	Protection resistor for high-voltage battery -N662- High-voltage battery pre-charging contactor -J1044-
4		4	Battery regulation control unit -J840-	4	Charging contactor 1 for direct current -J1052-	4 (4A)	Protection resistor for high-voltage battery -N662- High-voltage battery power contactor 1 -J1057-
		5		5	Charging contactor 2 for direct current -J1053-	5 (5A)	Current sensor for high-voltage battery -G848-
		6	Terminal 31	6		6 (6A)	High-voltage system fuse 1 -S350-
		7		7	High-voltage battery pre-charging contactor -J1044-	7 (1B)	High-voltage battery pre-charging contactor -J1044- High-voltage battery power contactor 1 -J1057-
		8	Terminal 31	8	High-voltage battery power contactor 1 -J1057-	8 (2B)	Charging contactor 2 for direct current -J1053-
		9	Terminal 31	9	High-voltage battery power contactor 2 -J1058-	9 (3B)	High-voltage system fuse 1 -S350-
		10	Terminal 30	10	Charging contactor 1 for direct current -J1052-	10 (4B)	Charging contactor 1 for direct current -J1052-
		11		11		11 (5B)	Current sensor for high-voltage battery -G848-
		12		12	Charging contactor 2 for direct current -J1053-	12 (6B)	High-voltage battery power contactor 2 -J1058-
		13	X5 Connection 1 (hybrid CAN bus, low), in engine wiring harness
		14	X4 Connection 1 (hybrid CAN bus, high), in engine wiring harness
		15
		16	Terminal 30
		17
		18	Terminal 31

Back to overview → Chapter

Battery regulation control unit -J840-

Fitting location:

in hybrid battery unit -AX1-

1 -	Battery regulation control unit -J840-

A -	32-pin connector -T32j-

Back to overview → Chapter

Connector assignment of battery regulation control unit -J840-

-T32j- (A)

Designation

-T32j– (A)

Designation

X4 Connection 1 (hybrid CAN bus, high), in engine wiring harness

Terminal 30

X5 Connection 1 (hybrid CAN bus, low), in engine wiring harness

E125 Connection 2 (powertrain CAN bus, high), in engine wiring harness

B384 Connection 2 (powertrain CAN bus, high), in main wiring harness

E126 Connection 2 (powertrain CAN bus low), in engine wiring harness

B391 Connection 2 (powertrain CAN bus, low), in main wiring harness

Module monitor control unit for batteries -J497-

Charging unit 1 for high-voltage battery -AX4-

t	Maintenance connector for high-voltage system -TW-

Pilot line

Battery module 0 -J1068-

Battery module 25 -J1084-

Airbag control unit -J234-

Terminal 30

Terminal 31

Terminal 30

Back to overview → Chapter

Fresh air blower control unit -J126-

Fitting location:

On heater and air conditioner unit, front passenger footwell.

1 -	Fresh air blower control unit -J126-

A -	4-pin connector -T4dc-

B -	2-pin connector -T2dq-

Back to overview → Chapter

Connector assignment of fresh air blower control unit -J126-

-T4dc- (A)

Designation

-T2dq- (B)

Designation

Terminal 31

Fresh air blower -V2-

Terminal 30

A209 Connection 1 (LIN bus) in dash panel wiring harness

Back to overview → Chapter

Interface for entry and start system -J965-

Interface for entry and start system -J965- , left-hand drive models

Fitting location:

Below the dash panel.

1 -	Interface for entry and start system -J965-

A -	32-pin connector -T32b-

Back to overview → Chapter

Connector assignment of interface for entry and start system -J965- , left-hand drive models

-T32b- (A)	Designation	-T32b– (A)	Designation
1		17	Terminal 31
2		18
3	Terminal 30	19	Interior aerial 1 for entry and start system -R138-
4		20	Rear bumper aerial for entry and start system -R136-
5	Front passenger door exterior handle contact sensor -G416-	21	Passenger side aerial for entry and start system -R135-
6		22	Luggage compartment aerial for entry and start system -R137-
7		23	Driver side aerial for entry and start system -R134-
8		24	Driver side aerial for entry and start system -R134-
9	Driver door exterior handle contact sensor -G415-	25	Luggage compartment aerial for entry and start system -R137-
10	Onboard supply control unit -J519-	26	Passenger side aerial for entry and start system -R135-
11		27	Rear bumper aerial for entry and start system -R136-
12		28	Interior aerial 1 for entry and start system -R138-
13		29
14		30	Ignition and starter button illumination bulb -L190-
15		31
16	B407 Connection 2 (convenience CAN bus, low), in main wiring harness	32	B398 Connection 2 (convenience CAN bus, high), in main wiring harness

Back to overview → Chapter

Interface for entry and start system -J965- , right-hand drive models

Fitting location:

Below the dash panel.

1 -	Interface for entry and start system -J965-

A -	32-pin connector -T32b-

q	Connector assignment identical to LHD → Anchor

Back to overview → Chapter

Didn't find what you were looking for? Try to find in:
- Mitchell onDemand online

- ETKA ONLINE - login-pass from kolhosniki.ru

- NEW ELSA ONLINE - login-pass from kolhosniki.ru

Suggestions, questions and wishes
Name:
E-mail:
Message:

Jose Maria de Pedro: Thank you so much for this information.

S: Hello, the transmission picking section is not working.

SIKORSKI: Hello I am looking for the Golf 7.Merco horn electrical diagrams

Валерий: hello how do i find the engine code

Rubén Darío de Jesús cedano : Good thank you

EDDY: Good day. Instructions on how to change the timing belt would be great. THANKS!

Podoaba Dan: Hello can you help us with a diagram or method for dismounting the gearbox...we have some bearings to change inside

леха: nothing works

Nick : Hi.skoda Octavia 2015 1.6 Manuel gearbox TDI how many litres gear box oil take

Mauro: can you please unlock audi A1 basic wiring diagrams? if possible also frame repair measures. Thank you

asier: I can't find the tightening torques for the gearbox to the engine block, for the engine mounts and engine mounts, and for the tightening torques for the oil pan

Mieszko: no power to keys touareg

Saulius: kdfasdf

Hector: Excellent very helpful thank you.

jose: I would like the fiat manuals, you don't have any

Nail: Good afternoon. who has the wiring diagram for the engine control skoda 2.0 czpa

Федор: Good afternoon! Where can I get an Audi repair manual?

Аноним: p

zenon valdez: Comfort control module 1d0 959 799 AH. Diagram

hedi: bjr I am looking to buy the shutter strips ref a94-10788 and a94-10849.. or???

Jose Vicente quinchiguango : many greetings to all

Polo: I need a part number for a rubber gasket that the electrical wireing for the dashboard. The one that goes through the fire-wall

Marco Walter: Have you updated the database? There is no image any more to the intake on the assembly overview page with all torque. Check link https://www.kolhosniki.ru/elsaonline&ver=150204&elsalang=en-GB&dir=rl&marke=N&modelljahr_numerisch=2005&mkb=AXA&gkb=FJN&karosserie=7HJ&ids=10249977&og_id=1624&bg_id=15958&rg_id=24&hkap_id=10249977&file=N.en-GB.k00589821.wi__75670881.xml_xsl--3

Stefan: Hello, i need auto data for Audi 1.9tdi 2003, timing belt, thank you

Alfonso: I need the manual for the replacement of a dual-mass flywheel and clutch for a Seat León 1p1 (mk2) 2007 1.9tdi BXE.

mariusz: Gearbox/differential a4 b8 avant quattro kbz 09r cdnc

Severiano Aguirre: Best regards

Станислав: Hello. I need a repair diagram for the main pair of Skoda Yeti 1.8, 2016 with bearing numbers

alex kostin: I need a diagram of all sensors. audi motor cduc

gabriel: Why don't I see the diagrams?

Аноним: based

Аноним: i love to shit my pants and then lick it up

Аноним: b

base-01: A

Алексей: Where did the Russian language go? There was a Russian language on Passat CC 2011, now it is not

Сергей: Please help, brake pad wear sensors, how are they connected to each other? On the diagram, they end without a connection 31,30,33,32,35,34

Alex: Hi! I would like to ask you for some help regarding a vw touran 1t3, 1.6 tdi, CAYC, fuses, relays and wiring diagram! Thank you very much!

jose gonzalez Montes: Hello, I need to buy all the wiring for the xenon headlights of a golf gti tdi special edition. Somewhere where I could get them.

Eduardo Javier: Information of the code 05709 and 05710 of Volskwagen Bora 2010, 2.5 lts

alegator: I will be glad to cooperate with you.

евгений кузьмин: there are instructions for the dsg gearbox

abdellaGaber: vw

Nico Josea: Workshop manual for VW 2005 BKD 2.0 TDI

Слава: I didn’t see the T5, as well as the cargo platform ..

твой папка: kuku epta

Evgenii: Please give access to wiring diagrams vas 6418

Thomas: Hello, what is the part number of the connector T18f? Thanks in advance... LG Thomas

Rob: Question, would like to completely remove cornering lights, so replace AFS control unit with LWR control unit. Now the question how I have to change the pin assignment???

Per Renlund: How can I log in?

Hans >>meier: LAWST

tom: Hello, super great site, unfortunately I can't find the assembly of the bearing frame for the 2.0tfsi on an audi a4 b7

loubens claude: hello, can you give me the conical distance of box t3 vwtransporteur ??? thank you for answer cdt (for an old gentleman of 80 years old former mecanicien.cdt

ussain sehli sahli: hello, I need to know the power pins of the airbag control unit for audi a4 b8 I have checked between the red and the ground and I only have 7.45 and when I remove the control unit I measure and it gives me 0v, can you tell me where the control unit is powered from? , Thank you

MOST: thank you for giving me access to the electrical diagrams

Günter: Is there a wiring diagram for installing aux on the Seat Leon 5F

carlo : Good evening, I would like to know the service of my car chassis n WAUZZZGA3JA067314

willl: 2010 audi q5 CAEB need pcm wire diagram please

роман: how can i find softcoding abs from this car

vaccum system 2.8 apr: Hello, send me all data photos for audi a6 c5 2.8 apr vaccum system,pls. BR, Piotr

Уваров Игорь: Of good! In the EBV automatic transmission, the front-wheel drive fell apart - the bearing in the differential, the shaft was damaged. You need to change the automatic transmission. Instead of an automatic transmission with the EBV marking, can you put an automatic transmission with a different marking?

german: I'm interested

Кирилл: The archive with the transmission is lost, information on it is needed.

Denis: Hi i need instructions about to repair V68 heater motor. Pole 9N

Vladimir: Huge thank you man! The information on the website was very helpful.

Erkki : How can I log in?

gide: super

Jose Silva: thanking the information that sometimes we do not have a budget to acquire the platform

petrov.vodkin.34: is the project alive?

ABDELKADER BOUYAHI: thank you for advance

Васил Радомиров: THANK YOU!

вал: what a divorce! Grandma threw and there are no schemes! In fact, they don't show up! reboot doesn't help

Валентин: no diagrams .reboot does not help

michel royer: how much should i tighten my distribution bolt and water pump on vw crafter 2011 thank you.

alberto: Hello

Juan: Thank you very much

Oleksii Dudka: please give me access to wiring diagrams

Tobyas: Check fan activation thermocontact

phillipe: very good

Аноним: well, damn it for sure) metropolitan tries

Humber: Great job! Have you a Happy New Year!!!

Ahmad Wees: hi

Ahmad: okay

yuriy: Thank you for your hard work. Great project. I hope that new information will be added as soon as possible. While trying to test. Thanks again. SUPER!!!

Sucuk : Wallah crises

Roger: Want a child from you!

Belebcir Mounir: hey

mounir: hey

guillermo hernandez balboa: TO REVIEW FAULT CODES

abdodyago: ABDO

abde lhakim: abdo

Darius : I need login and password

P1234: and

OK: thank you for advance

djji ram: Greetings

mohammed ali: hi sir this site is the best i have ever seen

NESMON: Hello, how to order at which address?

Дмитрий: The information on earth points for vw 614 polo does not display all the pictures. Refreshing the page doesn't help.

uttam kamble: image not open

артем: Please tell me how you can replace the QHX box with what letters

Horst: Thanks

Przemek: Hello, I do not know how to create an account on this site to be able to log in. I need a fog lamp diagram and a description for the electric box in the engine compartment and an additional one above the driver's legs. Regards

Аноним: Gifts, fuck!

C.Falke: Hello

M: Thanks

Антон: The site is not working, you will not see information here. some kind of paleonka and not a site.

Махота Евгений Александрович: what engine oil to use

binh: thanks

Владимир: Hello, A / M AUDI A4 B7 2.0TDI 2007, I want to change the multitronic to a manual gearbox on your site I found that two gearboxes were installed on my internal combustion engine (BPW), tell me how the manual transmission 01X with the letter designation HCF differs from JEM if they have the same gear ratios. And is it possible to put another gearbox with a higher torque for chipping an internal combustion engine up to 170hp? Or will these boxes last? Thanks.

hutaipali: Thanks

Bozkurt Motors: Hi

douadi: Greetings

Тимур: Good afternoon! You don't happen to have a diagram with tightening torques for automatic transmission aisin 09g KGV. We sort out the box, I want to do everything right

Trần Đăng Khoa: Yes, there is documentation for the 2015 Audi Q7 No about the airbag system

mario: I can't see the photos

Billy Jeteya: I want to register

Félix Martín-Monzú: Good Morning. I have an Audi A6 2.5 TDI 6 V registered in the year 2000, AUDI Type AFB 6/2496 cm3 engine (homologation *98/14/*0051. I want to know the equivalence of this engine with respect to the Euro 3, etc.) Can you provide me with this information? Thank you very much.

Aлексей: Good afternoon! If it's not difficult, check on ETKA what kind of oil to pour into the internal combustion engine now? WVGZZZ7LZ9D004533

Wojciech Kobylarski: I need login and password

АЛЕКСАНДР: Automatic transmission oil level control

janni: how do the camshafts have to be installed in the 2.0tfsi BWA

test: And

gerardo bravo: Hello

huynhmy: Hello

Ramy Elrefaey: how to register to this website?

john: were i can purchase this support plate 353 and 309

Аноним: a

Mieczysława Misiaszek: How to get to the stepper motor, the left side to replace the Turan car, manufactured in 2003

khaledauto: Hi,

Othmane: I want to share

khalid: hi, how much is the annual subscription to elsawin

Леонид Гладков: Hello I can't find a Vw T5 car due to fault 7H Tell me where in which database are the minibuses

Valeri: nothing opens or appears at all.

Виктор: You have the installation of the intake manifold tightening torque and sequence Skoda Tour 1.6BFQ

vaz: position empty weight on rear axle

PEDRO GARRIDO RIVERO: How can I remove the rear belt on the right side of the yeta?

Robert: Thank you

sadek : toledo 2014 need meter diagram and air conditioning diagram. fuel gauge and outdoor temperature sensor not working. shows -15 oC

ranulfo sauceda: good afternoon I need electrical diagram of transporter engine 2016 diesel

JESUS: proof

mark: Where to buy elsawin repair service manual?

mark: where the fuse of the 2.5 TDI 132kw starter on the dashboard at km illuminates FUSE

dotaz: Where is the starter fuse on the A6 2.5 TDI 132 kw

SVM Code: 4h0614517c NEED SVM CODE

Юрий: cant find for polo sedan 2016

gawel.cs: elsa no images are not loading

antonio: Hello

Andrei: error P2404 cannot find the problem, audi ku 5 2.0 TFSI USA CAEB

Achif: Fabia

File request: Good day. Can I ask for the A5_029_4M0907397ad_LED_EU.flash and A5_039_4M0907397ad_LED_EU.flash files

Krystian: Looking for a fuse chemistry for vw golf 4 1.6 75kw BFQ, FDH 2003, sales 1J10D3.

abed qadah: wiring diagram for g65

BELOUADI: Hi, nowhere can I find information on replacing the clutch with

Martin: bye, anyone ECU Pinout to 1.9 TDi AFN engine code?

AYMAN: please were can i find the file snk.s.en-us

muhammad mughal: Do you have anything for the Audi S6 (2013)

ayman: i want the file snk.s.en-us.cab

сергей: help with the selection of oil on the manual transmission 6 KNS

сергей: help with the selection of oil for manual transmission 6 KNS

сергей: box KNS

sukhbeer jangra: i have audi A4. when i scann ecuit show error that ecu is not installed in car. so i need ecu diagram with ecu wiring

Jose G. Marquez: Could it be that it is not included in your list because it is A3 8v 1.6 TDI 2017/3?

Jose G. Marquez: all in clear designation except traction type

ANDREAS: Hello with the brakes change discs and blocks what is the torque of the saddle holder and so?

Semen Shevchik: dq500

Semen Shevchik: Hi, nowhere can I find information on replacing the clutch with

Роман: Hi, we need data on the tightening torque of the bolts after replacing the pump injectors.

Lynn: Hello, I need all the repair manuals of SEAT, how can I get it

ELWAJJANI MOULAY RACHID: HELLO I HAVE ONLY PAYPAL FOR PAYMENT

Spac marcel Cosmin: sharan computer

Грайр : Good day. Nuena infa on the replacement of the cylinder head AXQ Touareg

Роман: There is no VW Amarok in the list of models, in offline ELSA there are both Amarok and Crafter.

Аноним: Turkot Can't find information on Vw t6,

javier : Buenas tardes. First of all, thank you very much for your contribution. I have a 2011 altea xl cfhc engine and npf box and the illustration of the timing belt change does not appear. You can check it or it's never going to come out. Many thanks and greetings

sergio : Thank you

Turkot: Can't find information on Vw t5 t6, what to do

schwanz : It should not be a secret how to fix a 20 twenty year old car! Thank you guys for giving this opportunity

Chris: Most helpful, thank you!

JOSE LUIS NAVARRO MENDEZ: Hi thanks

Hugo: Thank you very much for uploading Toledo 1M. fucking crack!

moha: hello I want to connect to elsawen

Николай: Good afternoon, did not find information about the Audi 100 1989 Quattro, KU engine. Maybe I'm doing something wrong

Китаев Роман: I threw it on the hosting. Please give access

darth vader: I threw it on the hosting. Please give access

victor manuel velazquez: Hello friend, I've been trying to get some information for 2 hours, but NOTHING

Carlos: about multivan 2.500cc 128kw

wolcar: elsawin access

Hugo: Hello friend! I am looking for the instructions for disassembly the rear bumper of a seat Toledo 1m 1999 but the images are empty, could you upload them again Thank you bro!

жОПА: NO FUCK MONEY YOU ARE ... FUCK BEggar

Вячеслав: recommended synchronization of pv and kv on brt engine

Antonio: Hello and thank you for sharing, my question is about the official repair times, I am especially interested, in any case, thanks again, greetings.-

Vlad: Donation made, what's next, no information

oscar: how to use the elsaweb

mateusz: Is there no possibility to pay support you in euro or dollars

mario : Pictures don't load anymore, you can't see anything

Евгений : in the selection of a gearbox for a Golf 4 for an AUM 1.8T engine - FYL and GPD - automatic gearboxes, and not a manual, as you indicated. Even type 09AF

Александр: Good. Thank you for the great service, but for the A6 C4 97 onwards. no diagram opens. Writes picture not found

Иван: Hello. please register.

Weekend: Fantastic. How can I support this

андрей скворцов: how to use, registration is necessary, I can not find where to register

quyet: hello i want to have a count in the elsa

James: Will ever be an eng version of VW database

Asdffg: bbjbhh

Роман: The author is great. Thank. Found everything I need! those who know how to use Elsa will find information here. Rather, the schemes would appear

Сергей Александрович : Che for a topic For what And the possibilities of all this. thank

Tim: It would be nice if you could also print out the repair guides

Jacek: Hello. Once elsa runs, I wanted to look for a motometer pinout.

Аркадий: Thank you very much for ELSA! Good job!

Руслан: Hello. And when the database update is completed There will be something new

Виталий: I have an ancient Vw t4 from 1998. Donated 10 re. Enter all the parameters of the car, clicked OK and nothing Question

NECR0MANCER: Buy yourself a car instead of an Audi!

Андрей: Q7 Links to internal MMI chapters do not work. But I got a general idea on my question. Thank.

илья: works fucking, with super style! keep it up, I hope you will finish it on my nifiga no you have to download and install

Place for your advertisement

Attention! Please use superetka.com/elsa

Please use superetka.com/elsa

PLEASE USE https://SUPERETKA.COM/elsaelsa on kolhosniki not support now!

Please use
superetka.com/elsa

PLEASE USE https://SUPERETKA.COM/elsa
elsa on kolhosniki not support now!