Yandex MC
Elsa online. ElsaWin. ElsaWeb. AudiPower unit4-cylinder TDI engine (2.0 ltr. 4-valve common rail), mechanicsExhaust systemExhaust systemRemoving and installing particulate filter

elsawin online

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru

Attention! Please use superetka.com/elsa

Audi A4 Avant 2009 >

Please use
superetka.com/elsa

PLEASE USE https://SUPERETKA.COM/elsa
elsa on kolhosniki not support now!

Removing and installing particulate filter
Removing
  Note
Fit all cable ties in the original positions when installing.
–  Remove front exhaust pipe → Chapter.
   
–  Unfasten connection -1-, remove bolt -2- and take out mounting for particulate filter.
  A21-10310
–  Remove exhaust gas temperature sender 4 -G648--1-.
–  Remove air cleaner housing →Rep. gr.23.
  A26-10683
–  Remove engine cover panel -arrows-.
  A10-11050
–  Unplug electrical connectors -1- for Lambda probe -G39- and -2- for exhaust gas temperature sender 3 -G495- and move clear.
–  Unplug electrical connector -3- for exhaust gas pressure sensor 1 -G450-.
–  Remove bolt -4-, unclip air hoses for exhaust gas pressure sensor 1 and remove from particulate filter.
  A10-11053
–  Remove exhaust gas temperature sender 3 -G495--3-.
–  Disconnect vacuum hose -1-.
–  Remove bolts -2- and -4-.
  A21-10306
  Note
Coolant hoses -1- and -2- must not be detached.
–  Remove bolts -arrows- and tie up exhaust gas recirculation cooler.
  A21-10307
–  Unfasten bolts -arrows- and remove bracket for exhaust gas recirculation.
  A26-10681
–  Remove nut -3- for exhaust gas recirculation pipe.
–  Remove bolts -4- and -5-, move exhaust gas recirculation pipe aside.
  Note
It is not possible to remove exhaust gas recirculation pipe.
  Note
t  On vehicles with auxiliary heater
t  Using hose clamps up to 25 mm -3094- clamp off coolant hoses at plenum chamber partition panel and detach from metal pipe.
t  Unfasten coolant line from suspension turret and longitudinal member and swivel to side.
  A26-10685
–  Remove nuts -1- to -3- on turbocharger.
  Note
Nut -1- is accessible from below on vehicles with auxiliary heater.
  A26-10168
–  Guide out particulate filter upwards -arrow-.
Installing
Install in reverse order. Note the following:
Tightening torques → Chapter „Exhaust system - exploded view“
Tightening torques → Chapter „Exhaust gas temperature senders - exploded view“
Tightening torques → Chapter „Exhaust gas recirculation system - exploded view“
  Note
Renew seals, gaskets and self-locking nuts.
–  After renewing particulate filter, perform "Adaption" in „Guided Functions“ mode → Vehicle diagnostic tester.
  A26-10682

Didn't find what you were looking for? Try to find in:
- Mitchell onDemand online
- Alldata Online (Beta)

- ETKA ONLINE - login-pass from kolhosniki.ru

- NEW ELSA ONLINE - login-pass from kolhosniki.ru
Loading...

This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20