Yandex MC
Elsa online. ElsaWin. ElsaWeb. AudiPower unit4-cylinder TDI unit injector engine (1.9 ltr.; 2.0 ltr. 2-valve), mechanicsEnginecrankshaft group, pistonsPoly V-belt drive - vehicles from 06.2003 onwardsPoly V-belt drive for power steering pump, alternator and air conditioner compressor - exploded view

elsawin online

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru

Attention! Please use superetka.com/elsa

Audi A4

Please use
superetka.com/elsa

PLEASE USE https://SUPERETKA.COM/elsa
elsa on kolhosniki not support now!

   
Poly V-belt drive for power steering pump, alternator and air conditioner compressor - exploded view
1 -  Poly V-belt
q   Check for wear
q   Before removing, mark direction of rotation with chalk or felt-tipped pen. If the belt runs in the opposite direction when it is refitted, this can cause breakage.
q   Removing and installing → Chapter
q   When installing, make sure it is properly seated on pulleys.
q   Routing of poly V-belt → 
2 -  Vibration damper
q   With pulley for poly V-belt
q   Can only be installed in one position
q   Removing and installing → Chapter
3 -  10 Nm + turn 90° further
q   Renew
4 -  Cover cap for vibration damper
5 -  23 Nm
6 -  Pulley for power steering pump
q   Counterhold with drift to unbolt
7 -  Poly V-belt tensioner
q   Use locking pin -T10060 A- to lock tensioner.
q   Removing and installing → Chapter
8 -  Dowel sleeve
q   Ensure correct seating in bracket
9 -  Not fitted
10 -  Not fitted
11 -  Bracket for ancillaries
q   Removing and installing → Chapter
12 -  23 Nm
13 -  Alternator
q   Removing and installing →Electrical system; Rep. Gr.27
q   To facilitate attachment of alternator, knock back threaded bushes for securing bolts slightly
14 -  23 Nm
15 -  23 Nm
16 -  Power steering pump
q   Removing and installing →Rep. Gr.48
q   To facilitate attachment of power steering pump, knock back threaded bush for securing bolt slightly
17 -  45 Nm
q   Observe correct tightening sequence → Fig.
18 -  Dowel sleeve
q   2x
q   Ensure correct seating in bracket
19 -  Air conditioner compressor
q   Do not unscrew or disconnect refrigerant hoses or pipes.
q   Removing and installing →Rep. Gr.87
q   When installing check dowel sleeves -item 18-
20 -  25 Nm
21 -  23 Nm
22 -  Idler roller for poly V-belt
q   Note installation position → Fig.
23 -  20 Nm + turn 90° further
q   Renew
24 -  Cover cap for idler roller

   
Routing of poly V-belt
1 -  Vibration damper
2 -  Poly V-belt tensioner
3 -  Poly V-belt
q   For alternator, power steering pump and air conditioner compressor
4 -  Alternator
5 -  Power steering pump
6 -  Idler roller
7 -  Air conditioner compressor

   
Tightening sequence for bracket for ancillaries
l  When installing, pay attention to dowel sleeve at top right between bracket and cylinder block.
–  Tighten bolts -1 … 6- hand-tight.
–  Tighten the bolts to 45 Nm in the sequence -1 … 6-.
   A13-10003
Installation position of idler roller
l  The side with the collar -arrow 1- faces the bolt, the flat side -arrow 2- faces the bracket.
   A13-10004

Didn't find what you were looking for? Try to find in:
- Mitchell onDemand online
- Alldata Online (Beta)

- ETKA ONLINE - login-pass from kolhosniki.ru

- NEW ELSA ONLINE - login-pass from kolhosniki.ru

This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20