Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



WITH C6

REMOVAL

CAUTION: All parts must be handled carefully to avoid nicking or burring the bearing or mating surfaces. Lubricate all internal parts with clean automatic transmission fluid before assembling them. Do not use any other lubricants except on gaskets and thrust washers. These may be coated with petroleum jelly to facilitate assembly. Always use new gaskets and seals when assembling transmission.

{tag}840570481@


1.Unfasten and remove parking pawl guide plate from case.
2.Remove spring, parking pawl, and shaft from case.
3.Working from the pan mounting surface, drill a 1/8 inch hole through center of cupped plug. Pull plug from case with a wire hook.
4.Lift end of spring off park plate pin to relieve tension.

{tag}840575231@


5.Thread a 1/4-20 X 1-1/4 inch bolt into park plate shaft. Pull shaft from case with screw.

INSTALLATION
1.Reverse procedure to install.

NOTE: When installing guide plate on case, make sure that actuating rod is seated in slot of plate.

WITH C6

REMOVAL

CAUTION: All parts must be handled carefully to avoid nicking or burring the bearing or mating surfaces. Lubricate all internal parts with clean automatic transmission fluid before assembling them. Do not use any other lubricants except on gaskets and thrust washers. These may be coated with petroleum jelly to facilitate assembly. Always use new gaskets and seals when assembling transmission.

Parking Pawl MechanismParking Pawl Mechanism



1.Unfasten and remove parking pawl guide plate from case.
2.Remove spring, parking pawl, and shaft from case.
3.Working from the pan mounting surface, drill a 1/8 inch hole through center of cupped plug. Pull plug from case with a wire hook.
4.Lift end of spring off park plate pin to relieve tension.

{tag}840575231@


5.Thread a 1/4-20 X 1-1/4 inch bolt into park plate shaft. Pull shaft from case with screw.

INSTALLATION
1.Reverse procedure to install.

NOTE: When installing guide plate on case, make sure that actuating rod is seated in slot of plate.

WITH C6

REMOVAL

CAUTION: All parts must be handled carefully to avoid nicking or burring the bearing or mating surfaces. Lubricate all internal parts with clean automatic transmission fluid before assembling them. Do not use any other lubricants except on gaskets and thrust washers. These may be coated with petroleum jelly to facilitate assembly. Always use new gaskets and seals when assembling transmission.

{tag}840570481@


1.Unfasten and remove parking pawl guide plate from case.
2.Remove spring, parking pawl, and shaft from case.
3.Working from the pan mounting surface, drill a 1/8 inch hole through center of cupped plug. Pull plug from case with a wire hook.
4.Lift end of spring off park plate pin to relieve tension.

Parking Plate Shaft ReplacementParking Plate Shaft Replacement



5.Thread a 1/4-20 X 1-1/4 inch bolt into park plate shaft. Pull shaft from case with screw.

INSTALLATION
1.Reverse procedure to install.

NOTE: When installing guide plate on case, make sure that actuating rod is seated in slot of plate.

WITH C6

REMOVAL

CAUTION: All parts must be handled carefully to avoid nicking or burring the bearing or mating surfaces. Lubricate all internal parts with clean automatic transmission fluid before assembling them. Do not use any other lubricants except on gaskets and thrust washers. These may be coated with petroleum jelly to facilitate assembly. Always use new gaskets and seals when assembling transmission.

Parking Pawl MechanismParking Pawl Mechanism



1.Unfasten and remove parking pawl guide plate from case.
2.Remove spring, parking pawl, and shaft from case.
3.Working from the pan mounting surface, drill a 1/8 inch hole through center of cupped plug. Pull plug from case with a wire hook.
4.Lift end of spring off park plate pin to relieve tension.

Parking Plate Shaft ReplacementParking Plate Shaft Replacement



5.Thread a 1/4-20 X 1-1/4 inch bolt into park plate shaft. Pull shaft from case with screw.

INSTALLATION
1.Reverse procedure to install.

NOTE: When installing guide plate on case, make sure that actuating rod is seated in slot of plate.




This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20