Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



OVERDRIVE RING GEAR AND CENTER SHAFT - WITH E4OD

REMOVAL

{tag}834604815@


NOTE: Refer to the Exploded View Of Overdrive Ring Gear And Center Shaft image when performing the following procedure.

1.Remove large outer race to ring gear retaining ring, then the one-way clutch assembly with inner and outer races.
2.Push out one-way clutch assembly and inner race, then separate race from clutch assembly.
3.Remove thrust washer No. 7L339 from front of overdrive planet assembly, then remove planet assembly from center shaft and ring gear.
4.Using a screwdriver, remove needle bearing assembly No. 7F240 from rear face of overdrive planet assembly.
5.Remove center shaft to ring gear wave-type snap ring, then the center shaft from ring gear.

INSTALLATION
1.Reverse procedure to install, noting the following:
a.Outer race assembly snap ring groove must be facing up.

{tag}834607331@


b.One-way clutch must be installed as shown in the Exploded View Of Overdrive Ring Gear And Center Shaft image and the One-Way Clutch Installation image.
c.Inner race must rotate counterclockwise from direction of installation.
OVERDRIVE RING GEAR AND CENTER SHAFT - WITH E4OD

REMOVAL

Exploded View Of Overdrive Ring Gear And Center ShaftExploded View Of Overdrive Ring Gear And Center Shaft



NOTE: Refer to the Exploded View Of Overdrive Ring Gear And Center Shaft image when performing the following procedure.

1.Remove large outer race to ring gear retaining ring, then the one-way clutch assembly with inner and outer races.
2.Push out one-way clutch assembly and inner race, then separate race from clutch assembly.
3.Remove thrust washer No. 7L339 from front of overdrive planet assembly, then remove planet assembly from center shaft and ring gear.
4.Using a screwdriver, remove needle bearing assembly No. 7F240 from rear face of overdrive planet assembly.
5.Remove center shaft to ring gear wave-type snap ring, then the center shaft from ring gear.

INSTALLATION
1.Reverse procedure to install, noting the following:
a.Outer race assembly snap ring groove must be facing up.

{tag}834607331@


b.One-way clutch must be installed as shown in the Exploded View Of Overdrive Ring Gear And Center Shaft image and the One-Way Clutch Installation image.
c.Inner race must rotate counterclockwise from direction of installation.
OVERDRIVE RING GEAR AND CENTER SHAFT - WITH E4OD

REMOVAL

{tag}834604815@


NOTE: Refer to the Exploded View Of Overdrive Ring Gear And Center Shaft image when performing the following procedure.

1.Remove large outer race to ring gear retaining ring, then the one-way clutch assembly with inner and outer races.
2.Push out one-way clutch assembly and inner race, then separate race from clutch assembly.
3.Remove thrust washer No. 7L339 from front of overdrive planet assembly, then remove planet assembly from center shaft and ring gear.
4.Using a screwdriver, remove needle bearing assembly No. 7F240 from rear face of overdrive planet assembly.
5.Remove center shaft to ring gear wave-type snap ring, then the center shaft from ring gear.

INSTALLATION
1.Reverse procedure to install, noting the following:
a.Outer race assembly snap ring groove must be facing up.

One-Way Clutch InstallationOne-Way Clutch Installation



b.One-way clutch must be installed as shown in the Exploded View Of Overdrive Ring Gear And Center Shaft image and the One-Way Clutch Installation image.
c.Inner race must rotate counterclockwise from direction of installation.
OVERDRIVE RING GEAR AND CENTER SHAFT - WITH E4OD

REMOVAL

Exploded View Of Overdrive Ring Gear And Center ShaftExploded View Of Overdrive Ring Gear And Center Shaft



NOTE: Refer to the Exploded View Of Overdrive Ring Gear And Center Shaft image when performing the following procedure.

1.Remove large outer race to ring gear retaining ring, then the one-way clutch assembly with inner and outer races.
2.Push out one-way clutch assembly and inner race, then separate race from clutch assembly.
3.Remove thrust washer No. 7L339 from front of overdrive planet assembly, then remove planet assembly from center shaft and ring gear.
4.Using a screwdriver, remove needle bearing assembly No. 7F240 from rear face of overdrive planet assembly.
5.Remove center shaft to ring gear wave-type snap ring, then the center shaft from ring gear.

INSTALLATION
1.Reverse procedure to install, noting the following:
a.Outer race assembly snap ring groove must be facing up.

One-Way Clutch InstallationOne-Way Clutch Installation



b.One-way clutch must be installed as shown in the Exploded View Of Overdrive Ring Gear And Center Shaft image and the One-Way Clutch Installation image.
c.Inner race must rotate counterclockwise from direction of installation.



This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20