Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



RECREATING THE SYMPTOM

In order to diagnose driveability problems, the technician must collect data on how the Electronic Engine Control (EEC-IV) system is sensing and reacting. After a thorough mechanical/visual inspection is completed, the EEC-IV portion of the Symptom Chart is diagnosed. Through the use of a monitor and a recorder, these signals can be inspected for shorts, opens, component failures, or erratic behavior. Also, the data received from the monitor and recorder can reveal the presence of mechanical problems.

PREPARATION

1.Place monitor (and recorder, if installed) in a convenient location inside the vehicle. Secure the cables away from any moving engine parts.
2.Place the proper overlay card on the monitor.
3.Copy list of EEC-IV sensors and actuators listed in the appropriate Symptom Chart. These signals will be monitored during the road test.
4.If a recorder is used, select the first 8 signals listed to channels 1-8 (one signal per channel). Connect the jumpers from the Input/Output (I/O) jacks to the appropriate channels.
5.Select the proper Diagnostic Reference Value Sheet. This sheet lists EEC-IV sensor and actuator values at various operating conditions.
NOTE: The values given on these sheets are only approximations.
6.In order to safely perform a road test, it is necessary that a second person accompany the driver. The second person can select signals, observe changes, and record notes.

USE OF PERIPHERAL INPUTS

Some useful signals listed in the Symptom Chart may require the use of certain peripheral (auxiliary) devices. These devices can be inserted into the AUX jacks of the monitor or the ADAPT 1/ADAPT 2 input jacks of the recorder.

REMINDERS

The purpose of the road test is to recreate the driveability problem by duplicating the conditions that caused it. The road test is a suggested but optional part of this section. It is important that the road test be performed safely. Use the provided seat belts and operate the vehicle in a safe manner, obeying all traffic rules and regulations.

OBSERVATIONS

During the road test various EEC-IV signals are chosen and their values shown. Also, the following observations can be made as the road test is performed:
-EEC-IV Values -- Compare road test values at various operating conditions with those listed in Diagnostic Reference Values. Refer to DIAGNOSTIC REFERENCE VALUES for more details.
-Monitor Lights -- Observation of the monitor lights give quick information about the condition of many EEC-IV signals. For example, these lights can quickly reveal the status of many signals, telling the technician whether an output should be energized or not. Optional signals are printed in yellow labels.
-Wiggle Tests -- By using the wiggle test mode during key ON engine RUNNING tests, often an intermittent device or wire will trigger the alarm. The Direct Current Voltage (DCV) wiggle mode in particular is very sensitive to sudden, erratic changes in an EEC-IV harness or component.

ROAD TEST PROCEDURE

1.Using the appropriate Symptom Chart, select the first listed EEC-IV device on monitor pin selector "A".
2.Turn ON the monitor (and recorder, if used). START and drive the vehicle.
3.If the recorder is installed, put the function switch in RECORD mode and and press the start record button.
4.Drive the vehicle, creating conditions associated with the driveability problem.
5.When the symptom occurs, the passenger should observe changes in the selected EEC-IV signal. Information should be recorded onto paper with other notes about the symptom, device, or operating conditions. If the recorder is used the capture button should be pressed.
6.Record information about the symptom, operating condition, and EEC-IV signal values received from the monitor (or recorder in playback mode).
7.If necessary, select other EEC-IV signals from the Symptom Chart and attempt to recreate the problem again. Observe and record the results. Go to ANALYZING DATA to interpret the data received from the road test.




This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20