Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



{tag}1364609502@


1.Disconnect battery ground cable. Discharge refrigerant from system.
2.Disconnect pressure switch electrical connector and remove from suction accumulator, Fig. 15.

{tag}1347196228@

3.Disconnect suction hose from accumulator, Fig. 2, and liquid line from evaporator core. Plug all open lines to prevent dirt and moisture contamination.
4.Remove nut retaining MAP sensor bracket to upper LH corner of evaporator case and remove spring clip holding sensor to housing, and position sensor aside.
5.Remove one nut retaining upper LH corner of evaporator case to dash panel, then remove six screws attaching LH evaporator cover to evaporator case.
6.Remove LH evaporator cover from case evaporator case.
7.Remove evaporator core and suction accumulator from evaporator case.
8.Reverse procedure to install. Use new O-rings lubricated with refrigerant oil.
9.Evacuate, charge and leak test system.



Fig. 15 Evaporator core removalFig. 15 Evaporator core removal



1.Disconnect battery ground cable. Discharge refrigerant from system.
2.Disconnect pressure switch electrical connector and remove from suction accumulator, Fig. 15.

{tag}1347196228@

3.Disconnect suction hose from accumulator, Fig. 2, and liquid line from evaporator core. Plug all open lines to prevent dirt and moisture contamination.
4.Remove nut retaining MAP sensor bracket to upper LH corner of evaporator case and remove spring clip holding sensor to housing, and position sensor aside.
5.Remove one nut retaining upper LH corner of evaporator case to dash panel, then remove six screws attaching LH evaporator cover to evaporator case.
6.Remove LH evaporator cover from case evaporator case.
7.Remove evaporator core and suction accumulator from evaporator case.
8.Reverse procedure to install. Use new O-rings lubricated with refrigerant oil.
9.Evacuate, charge and leak test system.



{tag}1364609502@


1.Disconnect battery ground cable. Discharge refrigerant from system.
2.Disconnect pressure switch electrical connector and remove from suction accumulator, Fig. 15.

Fig. 2 Spring lock coupling disconnect & connectFig. 2 Spring lock coupling disconnect & connect


3.Disconnect suction hose from accumulator, Fig. 2, and liquid line from evaporator core. Plug all open lines to prevent dirt and moisture contamination.
4.Remove nut retaining MAP sensor bracket to upper LH corner of evaporator case and remove spring clip holding sensor to housing, and position sensor aside.
5.Remove one nut retaining upper LH corner of evaporator case to dash panel, then remove six screws attaching LH evaporator cover to evaporator case.
6.Remove LH evaporator cover from case evaporator case.
7.Remove evaporator core and suction accumulator from evaporator case.
8.Reverse procedure to install. Use new O-rings lubricated with refrigerant oil.
9.Evacuate, charge and leak test system.



Fig. 15 Evaporator core removalFig. 15 Evaporator core removal



1.Disconnect battery ground cable. Discharge refrigerant from system.
2.Disconnect pressure switch electrical connector and remove from suction accumulator, Fig. 15.

Fig. 2 Spring lock coupling disconnect & connectFig. 2 Spring lock coupling disconnect & connect


3.Disconnect suction hose from accumulator, Fig. 2, and liquid line from evaporator core. Plug all open lines to prevent dirt and moisture contamination.
4.Remove nut retaining MAP sensor bracket to upper LH corner of evaporator case and remove spring clip holding sensor to housing, and position sensor aside.
5.Remove one nut retaining upper LH corner of evaporator case to dash panel, then remove six screws attaching LH evaporator cover to evaporator case.
6.Remove LH evaporator cover from case evaporator case.
7.Remove evaporator core and suction accumulator from evaporator case.
8.Reverse procedure to install. Use new O-rings lubricated with refrigerant oil.
9.Evacuate, charge and leak test system.






This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20