Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



CAUSES
-No assist from the brake booster. The vacuum operated brake booster may be defective or not receiving a sufficient supply of vacuum.
-Brake linings contaminated with brake fluid, oil, or grease. The contamination reduces the stopping ability of the brakes.
-Worn brake linings. Severely worn brake linings have a greatly reduced stopping ability.
-Glazed brake linings (overheated). Brake linings which have been severely overheated (cracked, shiny, charcoal like appearance) have a greatly reduced stopping ability.
-New brake linings not seated. Newly installed brake linings require a break in period of approximately 50 miles. Until the new brake linings are properly seated, overall braking performance will be less than 100%. Braking performance will gradually increase as the new linings are broken in.

Break-In Procedure
-Initially make 8-10 slow and gradual brake applications, slowing from 25 to 10 miles per hour.
-Severe braking or locking up the brakes should be avoided (unless dictated by an emergency or driver safety) for the first 50 miles.

WHAT TO CHECK FOR
-Check for proper brake booster operation.
-With the engine "OFF", depress and release the brake pedal 4-5 times.
{tag}1160025825@
-Depress the brake pedal firmly and start the engine.
-If the pedal goes down slightly the brake booster is operating properly.
-If the pedal does not go down slightly the brake booster is not assisting in brake operation. Verify vacuum supply to the booster.
-Maintain pressure on brake pedal while turning "OFF" engine. The pedal should remain in the same position. If the pedal slowly slowly rises, the booster or vacuum check valve is leaking. Replace as necessary.
-Verify the brake booster vacuum line is intact and installed properly. Verify that the vacuum check valve allows flow only towards the intake manifold, and not in reverse towards the booster.
-Verify that engine vacuum is at least 17 in hg.
-Inspect brake linings for sufficient thickness, contamination, and evidence of overheating. Replace as necessary.

CAUSES
-No assist from the brake booster. The vacuum operated brake booster may be defective or not receiving a sufficient supply of vacuum.
-Brake linings contaminated with brake fluid, oil, or grease. The contamination reduces the stopping ability of the brakes.
-Worn brake linings. Severely worn brake linings have a greatly reduced stopping ability.
-Glazed brake linings (overheated). Brake linings which have been severely overheated (cracked, shiny, charcoal like appearance) have a greatly reduced stopping ability.
-New brake linings not seated. Newly installed brake linings require a break in period of approximately 50 miles. Until the new brake linings are properly seated, overall braking performance will be less than 100%. Braking performance will gradually increase as the new linings are broken in.

Break-In Procedure
-Initially make 8-10 slow and gradual brake applications, slowing from 25 to 10 miles per hour.
-Severe braking or locking up the brakes should be avoided (unless dictated by an emergency or driver safety) for the first 50 miles.

WHAT TO CHECK FOR
-Check for proper brake booster operation.
-With the engine "OFF", depress and release the brake pedal 4-5 times.


-Depress the brake pedal firmly and start the engine.
-If the pedal goes down slightly the brake booster is operating properly.
-If the pedal does not go down slightly the brake booster is not assisting in brake operation. Verify vacuum supply to the booster.
-Maintain pressure on brake pedal while turning "OFF" engine. The pedal should remain in the same position. If the pedal slowly slowly rises, the booster or vacuum check valve is leaking. Replace as necessary.
-Verify the brake booster vacuum line is intact and installed properly. Verify that the vacuum check valve allows flow only towards the intake manifold, and not in reverse towards the booster.
-Verify that engine vacuum is at least 17 in hg.
-Inspect brake linings for sufficient thickness, contamination, and evidence of overheating. Replace as necessary.




This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20