Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



{tag}1142116185@
{tag}1141542571@
1.Clean ledge pads on backing plate, sanding lightly to bare metal.
2.Apply suitable lubricant to retracting and hold-down spring contacts on brake shoes and backing plate.
3.Apply suitable lubricant to threads and socket end of adjusting screw.
4.Install upper retracting spring on primary and secondary shoes and position shoe assembly on backing plate with wheel cylinder pushrods in shoe slots. For additional information see Brake Spring Removal and Installation Notes.
5.Install brake shoe hold-down springs.
6.Install brake shoe adjustment screw assembly with the slot in the head of adjustment screw facing primary shoe, lower retracting spring, adjusting lever, and lever spring assembly. Connect adjusting cable to adjusting lever. Socket end of each adjusting screw is stamped ``R or ``L to indicate use on right or left side of vehicle. Adjusting pivot nuts can be identified by number of lines machined around body of nut. Two lines indicate righthand nut and one line indicates lefthand nut.
7.Position cable in cable guide and install cable anchor fitting on the anchor pin.
8.Install parking brake assembly in anchor pin and secure with retaining nut behind backing plate.
9.On vehicles with full-floating axles, install brake drums as follows:
a.Place brake drum on hub and install attaching screws, bolts, or bolts and nuts.
b.Place hub and drum as an assembly on axle and start adjusting nut.
c.Adjust wheel bearing nut and install wheel bearing lock washer and lock nut. See Rear Axle for procedure.
d.Install new gasket and the bolts and lock washers.
e.Install wheel and tire assembly.
f.Adjust brakes.

For additional information see Notes, Warnings, and Hints. Exploded ViewExploded View

{tag}1141542571@
1.Clean ledge pads on backing plate, sanding lightly to bare metal.
2.Apply suitable lubricant to retracting and hold-down spring contacts on brake shoes and backing plate.
3.Apply suitable lubricant to threads and socket end of adjusting screw.
4.Install upper retracting spring on primary and secondary shoes and position shoe assembly on backing plate with wheel cylinder pushrods in shoe slots. For additional information see Brake Spring Removal and Installation Notes.
5.Install brake shoe hold-down springs.
6.Install brake shoe adjustment screw assembly with the slot in the head of adjustment screw facing primary shoe, lower retracting spring, adjusting lever, and lever spring assembly. Connect adjusting cable to adjusting lever. Socket end of each adjusting screw is stamped ``R or ``L to indicate use on right or left side of vehicle. Adjusting pivot nuts can be identified by number of lines machined around body of nut. Two lines indicate righthand nut and one line indicates lefthand nut.
7.Position cable in cable guide and install cable anchor fitting on the anchor pin.
8.Install parking brake assembly in anchor pin and secure with retaining nut behind backing plate.
9.On vehicles with full-floating axles, install brake drums as follows:
a.Place brake drum on hub and install attaching screws, bolts, or bolts and nuts.
b.Place hub and drum as an assembly on axle and start adjusting nut.
c.Adjust wheel bearing nut and install wheel bearing lock washer and lock nut. See Rear Axle for procedure.
d.Install new gasket and the bolts and lock washers.
e.Install wheel and tire assembly.
f.Adjust brakes.

For additional information see Notes, Warnings, and Hints. {tag}1142116185@
Assembled ViewAssembled View

1.Clean ledge pads on backing plate, sanding lightly to bare metal.
2.Apply suitable lubricant to retracting and hold-down spring contacts on brake shoes and backing plate.
3.Apply suitable lubricant to threads and socket end of adjusting screw.
4.Install upper retracting spring on primary and secondary shoes and position shoe assembly on backing plate with wheel cylinder pushrods in shoe slots. For additional information see Brake Spring Removal and Installation Notes.
5.Install brake shoe hold-down springs.
6.Install brake shoe adjustment screw assembly with the slot in the head of adjustment screw facing primary shoe, lower retracting spring, adjusting lever, and lever spring assembly. Connect adjusting cable to adjusting lever. Socket end of each adjusting screw is stamped ``R or ``L to indicate use on right or left side of vehicle. Adjusting pivot nuts can be identified by number of lines machined around body of nut. Two lines indicate righthand nut and one line indicates lefthand nut.
7.Position cable in cable guide and install cable anchor fitting on the anchor pin.
8.Install parking brake assembly in anchor pin and secure with retaining nut behind backing plate.
9.On vehicles with full-floating axles, install brake drums as follows:
a.Place brake drum on hub and install attaching screws, bolts, or bolts and nuts.
b.Place hub and drum as an assembly on axle and start adjusting nut.
c.Adjust wheel bearing nut and install wheel bearing lock washer and lock nut. See Rear Axle for procedure.
d.Install new gasket and the bolts and lock washers.
e.Install wheel and tire assembly.
f.Adjust brakes.

For additional information see Notes, Warnings, and Hints. Exploded ViewExploded View

Assembled ViewAssembled View

1.Clean ledge pads on backing plate, sanding lightly to bare metal.
2.Apply suitable lubricant to retracting and hold-down spring contacts on brake shoes and backing plate.
3.Apply suitable lubricant to threads and socket end of adjusting screw.
4.Install upper retracting spring on primary and secondary shoes and position shoe assembly on backing plate with wheel cylinder pushrods in shoe slots. For additional information see Brake Spring Removal and Installation Notes.
5.Install brake shoe hold-down springs.
6.Install brake shoe adjustment screw assembly with the slot in the head of adjustment screw facing primary shoe, lower retracting spring, adjusting lever, and lever spring assembly. Connect adjusting cable to adjusting lever. Socket end of each adjusting screw is stamped ``R or ``L to indicate use on right or left side of vehicle. Adjusting pivot nuts can be identified by number of lines machined around body of nut. Two lines indicate righthand nut and one line indicates lefthand nut.
7.Position cable in cable guide and install cable anchor fitting on the anchor pin.
8.Install parking brake assembly in anchor pin and secure with retaining nut behind backing plate.
9.On vehicles with full-floating axles, install brake drums as follows:
a.Place brake drum on hub and install attaching screws, bolts, or bolts and nuts.
b.Place hub and drum as an assembly on axle and start adjusting nut.
c.Adjust wheel bearing nut and install wheel bearing lock washer and lock nut. See Rear Axle for procedure.
d.Install new gasket and the bolts and lock washers.
e.Install wheel and tire assembly.
f.Adjust brakes.

For additional information see Notes, Warnings, and Hints.


This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20