Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



BRAKE PAD INSPECTION
Remove the pads/linings from the caliper and inspect for the following:
-The brake lining should be at least as thick as the backing-plate.
-The brake lining thickness should be at least 1/8 in (3mm) for riveted pads and 1/16 in (1.5mm) for non-riveted pads.
-Lining damage. The lining should not be cracked or glazed (shiny, glass or charcoal like appearance).
-Check the flatness of the pads/linings. Place the inboard and outboard lining surfaces together and check for a gap between the lining surfaces. This gap should not exceed 0.13 mm (.005-inch) at the middle of the lining surfaces. This applies to new or used pads/linings.

Replace the pads/linings if any problems are found.

{tag}1140242948@

The disc pads/linings have a wear indicator that makes a noise (metallic squeal) when the linings wear to a degree where replacement is required .


BRAKE CALIPER INSPECTION
Inspect the caliper for the following problems:
-Brake fluid leakage near or around the piston dust boot.
-Cracked caliper housing or piston.
-Uneven brake pad wear.
-The inner pad is worn more than the outer pad.
-The pads/linings from the left caliper are worn more than the right caliper (or vice versa).
-Missing or damaged mounting hardware.
-Caliper slide joints, slide pins, and bushings are free of corrosion and nicks
-Tears or cracks in dust boots around caliper pistons and slide assemblies.
-Evidence of excessive heat:
-Bluish purple discoloration of rotor or caliper housing.
-A thin brick red oxidation layer evenly covering all brake components on the hub assembly (not to be confused with the typical rough, and flaky oxidation caused by rust)

If any problems are identified with the above areas, the calipers should be replaced or rebuilt.

The Following Areas Should Also Be Inspected:
-Inspect the flexible brake hoses for cracks or signs of leakage. Replace if any defects are found.
-Inspect the splash guard around the rotor for damage or loose mounting bolts.

NOTE: The splash guard should not he permanently removed. The splash guard helps prevent debris and water from contacting the pad and caliper assembly and also helps funnel air across the brake components to assist in cooling.

-Inspect rear brake operation and adjustment. Rear brakes which are out of adjustment will require the front brakes to do more work, causing accelerated wear and possible overheating.



BRAKE PAD INSPECTION
Remove the pads/linings from the caliper and inspect for the following:
-The brake lining should be at least as thick as the backing-plate.
-The brake lining thickness should be at least 1/8 in (3mm) for riveted pads and 1/16 in (1.5mm) for non-riveted pads.
-Lining damage. The lining should not be cracked or glazed (shiny, glass or charcoal like appearance).
-Check the flatness of the pads/linings. Place the inboard and outboard lining surfaces together and check for a gap between the lining surfaces. This gap should not exceed 0.13 mm (.005-inch) at the middle of the lining surfaces. This applies to new or used pads/linings.

Replace the pads/linings if any problems are found.




The disc pads/linings have a wear indicator that makes a noise (metallic squeal) when the linings wear to a degree where replacement is required .


BRAKE CALIPER INSPECTION
Inspect the caliper for the following problems:
-Brake fluid leakage near or around the piston dust boot.
-Cracked caliper housing or piston.
-Uneven brake pad wear.
-The inner pad is worn more than the outer pad.
-The pads/linings from the left caliper are worn more than the right caliper (or vice versa).
-Missing or damaged mounting hardware.
-Caliper slide joints, slide pins, and bushings are free of corrosion and nicks
-Tears or cracks in dust boots around caliper pistons and slide assemblies.
-Evidence of excessive heat:
-Bluish purple discoloration of rotor or caliper housing.
-A thin brick red oxidation layer evenly covering all brake components on the hub assembly (not to be confused with the typical rough, and flaky oxidation caused by rust)

If any problems are identified with the above areas, the calipers should be replaced or rebuilt.

The Following Areas Should Also Be Inspected:
-Inspect the flexible brake hoses for cracks or signs of leakage. Replace if any defects are found.
-Inspect the splash guard around the rotor for damage or loose mounting bolts.

NOTE: The splash guard should not he permanently removed. The splash guard helps prevent debris and water from contacting the pad and caliper assembly and also helps funnel air across the brake components to assist in cooling.

-Inspect rear brake operation and adjustment. Rear brakes which are out of adjustment will require the front brakes to do more work, causing accelerated wear and possible overheating.






This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20