Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



{tag}1030366457@
{tag}1030368661@


Before disassembling any universal joint, examine the assembly carefully and note the position of the grease fitting (if used). Also, be sure to mark the yokes with relation to the propeller shaft so they may be reassembled in the same relative position. Failure to observe these precautions may produce rough vehicle operation which results in rapid wear and failure of parts, and place an unbalanced load on transmission, engine and rear axle.

When universal joints are disassembled for lubrication or inspection, and the old parts are to be reinstalled, special care must be exercised to avoid damage to universal joint spider or cross and bearing cups. Some driveshafts use an injected nylon retainer on the universal joint bearings. When service is necessary, pressing the bearings out will sheer the nylon retainer, Fig. 1. Replacement with the conventional steel snap ring type is then necessary, Fig. 2.
Fig. 1 Production Type Universal Joint Which Use Nylon Injection Rings In Place Of Snap RingsFig. 1 Production Type Universal Joint Which Use Nylon Injection Rings In Place Of Snap Rings

{tag}1030368661@


Before disassembling any universal joint, examine the assembly carefully and note the position of the grease fitting (if used). Also, be sure to mark the yokes with relation to the propeller shaft so they may be reassembled in the same relative position. Failure to observe these precautions may produce rough vehicle operation which results in rapid wear and failure of parts, and place an unbalanced load on transmission, engine and rear axle.

When universal joints are disassembled for lubrication or inspection, and the old parts are to be reinstalled, special care must be exercised to avoid damage to universal joint spider or cross and bearing cups. Some driveshafts use an injected nylon retainer on the universal joint bearings. When service is necessary, pressing the bearings out will sheer the nylon retainer, Fig. 1. Replacement with the conventional steel snap ring type is then necessary, Fig. 2.
{tag}1030366457@
Fig. 2 Service Type Universal Joint (Internal Snap Ring Type)Fig. 2 Service Type Universal Joint (Internal Snap Ring Type)



Before disassembling any universal joint, examine the assembly carefully and note the position of the grease fitting (if used). Also, be sure to mark the yokes with relation to the propeller shaft so they may be reassembled in the same relative position. Failure to observe these precautions may produce rough vehicle operation which results in rapid wear and failure of parts, and place an unbalanced load on transmission, engine and rear axle.

When universal joints are disassembled for lubrication or inspection, and the old parts are to be reinstalled, special care must be exercised to avoid damage to universal joint spider or cross and bearing cups. Some driveshafts use an injected nylon retainer on the universal joint bearings. When service is necessary, pressing the bearings out will sheer the nylon retainer, Fig. 1. Replacement with the conventional steel snap ring type is then necessary, Fig. 2.
Fig. 1 Production Type Universal Joint Which Use Nylon Injection Rings In Place Of Snap RingsFig. 1 Production Type Universal Joint Which Use Nylon Injection Rings In Place Of Snap Rings

Fig. 2 Service Type Universal Joint (Internal Snap Ring Type)Fig. 2 Service Type Universal Joint (Internal Snap Ring Type)



Before disassembling any universal joint, examine the assembly carefully and note the position of the grease fitting (if used). Also, be sure to mark the yokes with relation to the propeller shaft so they may be reassembled in the same relative position. Failure to observe these precautions may produce rough vehicle operation which results in rapid wear and failure of parts, and place an unbalanced load on transmission, engine and rear axle.

When universal joints are disassembled for lubrication or inspection, and the old parts are to be reinstalled, special care must be exercised to avoid damage to universal joint spider or cross and bearing cups. Some driveshafts use an injected nylon retainer on the universal joint bearings. When service is necessary, pressing the bearings out will sheer the nylon retainer, Fig. 1. Replacement with the conventional steel snap ring type is then necessary, Fig. 2.



This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20