Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



Disassembly

1.Place driveshaft in a vise using care to avoid damaging it.
2.Remove bearing retaining snap rings. Some universal joints use injected nylon retainers in place of snap rings. During servicing, the snap rings supplied with the replacement universal joint assembly must be used.

{tag}1029874379@
{tag}1029876133@

3.Position tool on shaft and press bearing out of yoke, Fig. 4. If bearing cannot be pressed all the way out, remove it using vise grips or channel lock pliers or position driveshaft as shown and strike center yoke with hammer, Fig. 5. Mark yoke and shaft to make sure they will be reassembled in their same relative positions.
4.Reposition tool so that it presses on the spider in order to press other bearing from opposite side of flange.
5.If used, remove flange from spider.

Assembly

1.Start new bearing into yoke, then position spider into yoke and press bearing until it is 1/4 inch below surface.
2.Remove tool and install a new snap ring.
3.Start new bearing in opposite side of yoke, then install tool and press on bearing until opposite bearing contacts snap ring.
4.Remove tool and install remaining snap ring.
Disassembly

1.Place driveshaft in a vise using care to avoid damaging it.
2.Remove bearing retaining snap rings. Some universal joints use injected nylon retainers in place of snap rings. During servicing, the snap rings supplied with the replacement universal joint assembly must be used.

Fig. 4 Removing Bearing Caps Using Tool And AdapterFig. 4 Removing Bearing Caps Using Tool And Adapter

{tag}1029876133@

3.Position tool on shaft and press bearing out of yoke, Fig. 4. If bearing cannot be pressed all the way out, remove it using vise grips or channel lock pliers or position driveshaft as shown and strike center yoke with hammer, Fig. 5. Mark yoke and shaft to make sure they will be reassembled in their same relative positions.
4.Reposition tool so that it presses on the spider in order to press other bearing from opposite side of flange.
5.If used, remove flange from spider.

Assembly

1.Start new bearing into yoke, then position spider into yoke and press bearing until it is 1/4 inch below surface.
2.Remove tool and install a new snap ring.
3.Start new bearing in opposite side of yoke, then install tool and press on bearing until opposite bearing contacts snap ring.
4.Remove tool and install remaining snap ring.
Disassembly

1.Place driveshaft in a vise using care to avoid damaging it.
2.Remove bearing retaining snap rings. Some universal joints use injected nylon retainers in place of snap rings. During servicing, the snap rings supplied with the replacement universal joint assembly must be used.

{tag}1029874379@
Fig. 5 Removing Bearing Cap By Holding In A Vice And Striking Center Yoke With HammerFig. 5 Removing Bearing Cap By Holding In A Vice And Striking Center Yoke With Hammer


3.Position tool on shaft and press bearing out of yoke, Fig. 4. If bearing cannot be pressed all the way out, remove it using vise grips or channel lock pliers or position driveshaft as shown and strike center yoke with hammer, Fig. 5. Mark yoke and shaft to make sure they will be reassembled in their same relative positions.
4.Reposition tool so that it presses on the spider in order to press other bearing from opposite side of flange.
5.If used, remove flange from spider.

Assembly

1.Start new bearing into yoke, then position spider into yoke and press bearing until it is 1/4 inch below surface.
2.Remove tool and install a new snap ring.
3.Start new bearing in opposite side of yoke, then install tool and press on bearing until opposite bearing contacts snap ring.
4.Remove tool and install remaining snap ring.
Disassembly

1.Place driveshaft in a vise using care to avoid damaging it.
2.Remove bearing retaining snap rings. Some universal joints use injected nylon retainers in place of snap rings. During servicing, the snap rings supplied with the replacement universal joint assembly must be used.

Fig. 4 Removing Bearing Caps Using Tool And AdapterFig. 4 Removing Bearing Caps Using Tool And Adapter

Fig. 5 Removing Bearing Cap By Holding In A Vice And Striking Center Yoke With HammerFig. 5 Removing Bearing Cap By Holding In A Vice And Striking Center Yoke With Hammer


3.Position tool on shaft and press bearing out of yoke, Fig. 4. If bearing cannot be pressed all the way out, remove it using vise grips or channel lock pliers or position driveshaft as shown and strike center yoke with hammer, Fig. 5. Mark yoke and shaft to make sure they will be reassembled in their same relative positions.
4.Reposition tool so that it presses on the spider in order to press other bearing from opposite side of flange.
5.If used, remove flange from spider.

Assembly

1.Start new bearing into yoke, then position spider into yoke and press bearing until it is 1/4 inch below surface.
2.Remove tool and install a new snap ring.
3.Start new bearing in opposite side of yoke, then install tool and press on bearing until opposite bearing contacts snap ring.
4.Remove tool and install remaining snap ring.



This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20