Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR IS MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.

CAUTION:
-Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system
-Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water.

NOTE: When any part of the hydraulic system has been disconnected for repair or replacement, air may get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been properly connected. The hydraulic system can be bled manually or with pressure bleeding equipment.

{tag}226600787@

1.Disconnect the brake master cylinder outlet tubes.

NOTE: When the brake master cylinder has been replaced or the system has been emptied, or partially emptied, it should be primed to prevent air from getting into the system.

{tag}226605459@

2.Install short brake tubes with ends submerged in the brake master cylinder reservoir and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
3.Have an assistant pump the brake pedal until clear fluid flows from both brake tubes without air bubbles.
4.Remove the short brake tubes and install the brake outlet tubes.
5.Bleed each brake tube at the brake master cylinder as follows:
1Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal.
2Loosen the rearmost brake tube fittings until a stream of brake fluid comes out. Have an assistant maintain pressure on the brake pedal while tightening the brake tube fitting.
3Repeat this operation until clear, bubble-free fluid comes out.
4Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube.

{tag}226676550@

6.While the assistant maintains pressure on the brake pedal, tighten the brake tubes.


WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR IS MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.

CAUTION:
-Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system
-Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water.

NOTE: When any part of the hydraulic system has been disconnected for repair or replacement, air may get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been properly connected. The hydraulic system can be bled manually or with pressure bleeding equipment.




1.Disconnect the brake master cylinder outlet tubes.

NOTE: When the brake master cylinder has been replaced or the system has been emptied, or partially emptied, it should be primed to prevent air from getting into the system.

{tag}226605459@

2.Install short brake tubes with ends submerged in the brake master cylinder reservoir and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
3.Have an assistant pump the brake pedal until clear fluid flows from both brake tubes without air bubbles.
4.Remove the short brake tubes and install the brake outlet tubes.
5.Bleed each brake tube at the brake master cylinder as follows:
1Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal.
2Loosen the rearmost brake tube fittings until a stream of brake fluid comes out. Have an assistant maintain pressure on the brake pedal while tightening the brake tube fitting.
3Repeat this operation until clear, bubble-free fluid comes out.
4Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube.

{tag}226676550@

6.While the assistant maintains pressure on the brake pedal, tighten the brake tubes.


WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR IS MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.

CAUTION:
-Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system
-Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water.

NOTE: When any part of the hydraulic system has been disconnected for repair or replacement, air may get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been properly connected. The hydraulic system can be bled manually or with pressure bleeding equipment.

{tag}226600787@

1.Disconnect the brake master cylinder outlet tubes.

NOTE: When the brake master cylinder has been replaced or the system has been emptied, or partially emptied, it should be primed to prevent air from getting into the system.




2.Install short brake tubes with ends submerged in the brake master cylinder reservoir and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
3.Have an assistant pump the brake pedal until clear fluid flows from both brake tubes without air bubbles.
4.Remove the short brake tubes and install the brake outlet tubes.
5.Bleed each brake tube at the brake master cylinder as follows:
1Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal.
2Loosen the rearmost brake tube fittings until a stream of brake fluid comes out. Have an assistant maintain pressure on the brake pedal while tightening the brake tube fitting.
3Repeat this operation until clear, bubble-free fluid comes out.
4Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube.

{tag}226676550@

6.While the assistant maintains pressure on the brake pedal, tighten the brake tubes.


WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR IS MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.

CAUTION:
-Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system
-Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water.

NOTE: When any part of the hydraulic system has been disconnected for repair or replacement, air may get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been properly connected. The hydraulic system can be bled manually or with pressure bleeding equipment.




1.Disconnect the brake master cylinder outlet tubes.

NOTE: When the brake master cylinder has been replaced or the system has been emptied, or partially emptied, it should be primed to prevent air from getting into the system.




2.Install short brake tubes with ends submerged in the brake master cylinder reservoir and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
3.Have an assistant pump the brake pedal until clear fluid flows from both brake tubes without air bubbles.
4.Remove the short brake tubes and install the brake outlet tubes.
5.Bleed each brake tube at the brake master cylinder as follows:
1Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal.
2Loosen the rearmost brake tube fittings until a stream of brake fluid comes out. Have an assistant maintain pressure on the brake pedal while tightening the brake tube fitting.
3Repeat this operation until clear, bubble-free fluid comes out.
4Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube.

{tag}226676550@

6.While the assistant maintains pressure on the brake pedal, tighten the brake tubes.


WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR IS MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.

CAUTION:
-Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system
-Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water.

NOTE: When any part of the hydraulic system has been disconnected for repair or replacement, air may get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been properly connected. The hydraulic system can be bled manually or with pressure bleeding equipment.

{tag}226600787@

1.Disconnect the brake master cylinder outlet tubes.

NOTE: When the brake master cylinder has been replaced or the system has been emptied, or partially emptied, it should be primed to prevent air from getting into the system.

{tag}226605459@

2.Install short brake tubes with ends submerged in the brake master cylinder reservoir and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
3.Have an assistant pump the brake pedal until clear fluid flows from both brake tubes without air bubbles.
4.Remove the short brake tubes and install the brake outlet tubes.
5.Bleed each brake tube at the brake master cylinder as follows:
1Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal.
2Loosen the rearmost brake tube fittings until a stream of brake fluid comes out. Have an assistant maintain pressure on the brake pedal while tightening the brake tube fitting.
3Repeat this operation until clear, bubble-free fluid comes out.
4Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube.




6.While the assistant maintains pressure on the brake pedal, tighten the brake tubes.


WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR IS MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.

CAUTION:
-Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system
-Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water.

NOTE: When any part of the hydraulic system has been disconnected for repair or replacement, air may get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been properly connected. The hydraulic system can be bled manually or with pressure bleeding equipment.




1.Disconnect the brake master cylinder outlet tubes.

NOTE: When the brake master cylinder has been replaced or the system has been emptied, or partially emptied, it should be primed to prevent air from getting into the system.

{tag}226605459@

2.Install short brake tubes with ends submerged in the brake master cylinder reservoir and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
3.Have an assistant pump the brake pedal until clear fluid flows from both brake tubes without air bubbles.
4.Remove the short brake tubes and install the brake outlet tubes.
5.Bleed each brake tube at the brake master cylinder as follows:
1Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal.
2Loosen the rearmost brake tube fittings until a stream of brake fluid comes out. Have an assistant maintain pressure on the brake pedal while tightening the brake tube fitting.
3Repeat this operation until clear, bubble-free fluid comes out.
4Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube.




6.While the assistant maintains pressure on the brake pedal, tighten the brake tubes.


WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR IS MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.

CAUTION:
-Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system
-Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water.

NOTE: When any part of the hydraulic system has been disconnected for repair or replacement, air may get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been properly connected. The hydraulic system can be bled manually or with pressure bleeding equipment.

{tag}226600787@

1.Disconnect the brake master cylinder outlet tubes.

NOTE: When the brake master cylinder has been replaced or the system has been emptied, or partially emptied, it should be primed to prevent air from getting into the system.




2.Install short brake tubes with ends submerged in the brake master cylinder reservoir and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
3.Have an assistant pump the brake pedal until clear fluid flows from both brake tubes without air bubbles.
4.Remove the short brake tubes and install the brake outlet tubes.
5.Bleed each brake tube at the brake master cylinder as follows:
1Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal.
2Loosen the rearmost brake tube fittings until a stream of brake fluid comes out. Have an assistant maintain pressure on the brake pedal while tightening the brake tube fitting.
3Repeat this operation until clear, bubble-free fluid comes out.
4Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube.




6.While the assistant maintains pressure on the brake pedal, tighten the brake tubes.


WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR IS MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.

CAUTION:
-Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system
-Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water.

NOTE: When any part of the hydraulic system has been disconnected for repair or replacement, air may get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been properly connected. The hydraulic system can be bled manually or with pressure bleeding equipment.




1.Disconnect the brake master cylinder outlet tubes.

NOTE: When the brake master cylinder has been replaced or the system has been emptied, or partially emptied, it should be primed to prevent air from getting into the system.




2.Install short brake tubes with ends submerged in the brake master cylinder reservoir and fill the brake master cylinder reservoir with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
3.Have an assistant pump the brake pedal until clear fluid flows from both brake tubes without air bubbles.
4.Remove the short brake tubes and install the brake outlet tubes.
5.Bleed each brake tube at the brake master cylinder as follows:
1Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal.
2Loosen the rearmost brake tube fittings until a stream of brake fluid comes out. Have an assistant maintain pressure on the brake pedal while tightening the brake tube fitting.
3Repeat this operation until clear, bubble-free fluid comes out.
4Refill the brake master cylinder reservoir as necessary. Repeat the bleeding operation at the front brake tube.




6.While the assistant maintains pressure on the brake pedal, tighten the brake tubes.





This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20