Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.


{tag}216643040@


1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.


{tag}216644050@


2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.


{tag}216645928@


3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.


{tag}216648080@


4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.






1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.


{tag}216644050@


2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.


{tag}216645928@


3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.


{tag}216648080@


4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.


{tag}216643040@


1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.






2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.


{tag}216645928@


3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.


{tag}216648080@


4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.






1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.






2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.


{tag}216645928@


3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.


{tag}216648080@


4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.


{tag}216643040@


1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.


{tag}216644050@


2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.






3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.


{tag}216648080@


4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.






1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.


{tag}216644050@


2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.






3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.


{tag}216648080@


4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.


{tag}216643040@


1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.






2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.






3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.


{tag}216648080@


4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.






1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.






2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.






3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.


{tag}216648080@


4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.


{tag}216643040@


1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.


{tag}216644050@


2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.


{tag}216645928@


3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.






4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.






1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.


{tag}216644050@


2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.


{tag}216645928@


3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.






4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.


{tag}216643040@


1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.






2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.


{tag}216645928@


3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.






4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.






1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.






2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.


{tag}216645928@


3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.






4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.


{tag}216643040@


1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.


{tag}216644050@


2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.






3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.






4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.






1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.


{tag}216644050@


2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.






3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.






4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.


{tag}216643040@


1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.






2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.






3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.






4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.
CAUTION: During normal A/C operation, oil is circulated through the system with the refrigerant, and a small amount is retained in each component. If certain components of the system are removed for replacement, some of the refrigerant oil will go with the component. To maintain the original total oil charge, it is necessary to compensate for the oil lost by adding oil to the system with the replacement part.






1.Rotate the A/C compressor shaft six to eight revolutions while collecting oil in a clean measuring device.
-If the amount of oil drained from the old A/C compressor is between 85-142 ml (3-5 ounces), pour the same amount plus 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is greater than 142 ml (5 ounces), pour the same amount drained of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor.
-If the amount of oil that was removed from the old A/C compressor is less than 85 ml (3 ounces), pour 85 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B into the new A/C compressor

NOTE: Service A/C compressors are shipped without compressor oil.






2.For the suction accumulator/drier, drill two 1/2 inch holes in the suction accumulator/drier cylinder and drain the oil into a calibrated container.
1Add a quantity of new oil to match that drained from the old suction accumulator/drier plus 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B.






3.For the A/C evaporator core, add 89 ml (3 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube.






4.For the A/C condenser core, add 30 ml (1 ounce) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the A/C condenser core or the suction accumulator/drier inlet tube.
5.Add 60 ml (2 ounces) of clean Motorcraft YN-12b refrigerant oil F2AZ-19577-AC (Canada: Motorcraft CYN-12b) or equivalent meeting Ford specification WSH-M1C231-B to the suction accumulator/drier inlet tube when performing each of the following repairs:
-replacement of the A/C evaporator core orifice
-replacement of the A/C compressor pressure relief valve
-replacement of a refrigerant line
-repair of an O-ring leak
-repair of a charge port leak
6.Replacement of components that do not require discharge of refrigerant and resulting oil loss, such as the A/C cycling switch and the A/C pressure transducer, do not require additional oil.



This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20