Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION

{tag}163443924@

1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.

{tag}163442568@

6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.

{tag}163441164@

5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.

{tag}163439963@

4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.

{tag}163437486@

3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.
REMOVAL
1.Disconnect the battery ground cable.
2.Remove the steering wheel.




3.Twist off the cap from the ignition switch lock cylinder.




4.Remove the ignition switch lock cylinder.
-Use a 3/8-inch diameter drill to drill down the middle of the ignition lock key slot until the ignition switch lock cylinder breaks loose.
-Remove and discard the ignition switch lock cylinder and drill shavings from the steering column.




5.Remove the bearing retainer.




6.Remove the bearing and the gear.
-Thoroughly clean all drill shavings from the steering column and inspect for damage.

INSTALLATION




1.To install, reverse the removal procedure, using a new ignition switch lock cylinder.
-Verify ignition switch lock cylinder operation.

NOTE:
-When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
-Use a new ignition switch lock cylinder.



This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20