Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION

{tag}133199484@

1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.

{tag}133196111@

6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.

{tag}133192418@

5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.

{tag}133190300@

4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.

{tag}133187377@

3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.

{tag}133186196@

2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
REMOVAL
1.Disconnect the battery ground cable.




2.Remove the ignition switch lock cylinder.
(1)Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
(2)Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.




3.Twist the tilt wheel handle and shank and remove.




4.Release the four clips and remove the steering column opening cover.

NOTE: Move gear selector to lowest position to access steering column opening cover.




5.Remove the upper and lower steering column shrouds.
(1)Remove the three screws.
(2)Remove the lower steering column shroud.
(3)Remove the upper steering column shroud.




6.Remove the multi-function switch.
(1)Remove the two screws.
(2)Disconnect the electrical connectors.
(3)Remove the multi-function switch.

INSTALLATION




1.To install, reverse the removal procedure.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.



This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20