Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.

{tag}1253566044@

2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION

{tag}1253497803@

1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.

{tag}1253582297@

4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.

{tag}1253493362@

3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.

{tag}1253491012@

2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

REMOVAL
WARNING:
-ALWAYS WEAR SAFETY GLASSES WHEN SERVICING AN AIR BAG VEHICLE AND WHEN HANDLING AN AIR BAG.
-CARRY A LIVE AIR BAG WITH THE BAG AND TRIM COVER POINTED AWAY FROM YOUR BODY. AN ACCIDENTAL DEPLOYMENT WILL THEN DEPLOY WITH A MINIMAL CHANCE OF INJURY.
-PLACE A LIVE AIR BAG ON A BENCH OR OTHER SURFACE WITH THE TRIM COVER UP.
-AFTER DEPLOYMENT, THE AIR BAG SURFACE MAY CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTER HANDLING A DEPLOYED AIR BAG.
-NEVER PROBE THE CONNECTORS ON THE AIR BAGS. DOING SO MAY RESULT IN AIR BAG DEPLOYMENT WHICH COULD RESULT IN PERSONAL INJURY.
-AIR BAG MODULES WITH DISCOLORED OR DAMAGED COVERS OR DEPLOYMENT DOORS MUST BE REPLACED, NOT REPAINTED.
-VEHICLE SENSOR ORIENTATION IS CRITICAL FOR PROPER SYSTEM OPERATION. IF A VEHICLE EQUIPPED WITH AN AIR BAG SYSTEM IS INVOLVED IN A COLLISION, INSPECT THE SENSOR MOUNTING BRACKET AND WING PIGTAIL FOR DEFORMATION. IF DAMAGED, THE SENSOR SHOULD BE REPLACED WHETHER OR NOT THE AIR BAG IS DEPLOYED.

1.Remove the battery cables.
(1)Remove the battery ground cable.
(2)Remove the battery to starter relay cable and wait one minute for the backup power supply to be depleted.

NOTE: Make sure the front wheels are in the straight-ahead position.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY TO STARTER RELAY CABLE AND WAIT ONE MINUTE.




2.Remove the driver side air bag module.
(1)Remove the two screws.
(2)Disconnect the air bag sliding contact electrical connector.
(3)Disconnect the horn electrical connector.
(4)Remove the driver side air bag module.




3.Remove the steering wheel bolt.




4.Use (A) 2-Jaw Puller to remove the steering wheel.

CAUTION: Removing the steering wheel without using a puller can damage the column bearings.

INSTALLATION




1.Install the steering wheel.
(1)Position the steering wheel.
(2)Install the bolt.




2.Install the driver side air bag module.
(1)Connect the air bag sliding contact electrical connector.
(2)Connect the horn electrical connector.
(3)Position the driver side air bag module.
(4)Install the two screws.

3.Connect the battery cables.
(1)Connect the battery to starter relay cable.
(2)Connect the battery ground cable.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.




This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20