Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.

{tag}1246574484@

13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.

{tag}1246552843@

12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.

{tag}1246550019@

8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.

{tag}1246550019@

11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.

{tag}1246532894@

10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.

{tag}1246528436@

7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.

{tag}1246545603@

5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.

{tag}1246523231@

4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.
{tag}1246520390@

1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



1.Turn the steering wheel from right stop to left stop at least once.

NOTE: The engine should not be running.

2.Remove the driver side air bag.
3.Raise and support the vehicle.




4.Remove the steering sector shaft arm drag link castellated nut.
(1)Remove the cotter pin.
(2)Remove the castellated nut.




5.Use Pitman Arm Puller to separate the steering sector shaft arm drag link.
6.Lower and support the front of the vehicle.

NOTE: The front wheels should not touch the ground.




7.Attach a inch lb torque wrench to the (A) bolt and measure the steering gear meshload from center.

NOTE: Reset the steering gear meshload only if the measured rotating torque for total on-center load is less than specification.




8.Meshload adjustment is necessary if out of specification.
9.Remove the fan blade assembly and fan shroud to access the sector shaft locknut.




10.Adjust the sector shaft to proper rotating torque.
(1)Hold the sector shaft and loosen the meshload adjuster locknut.
(2)Adjust the sector shaft.




11.Verify that the rotating torque is to specification.
-Readjust if necessary.




12.Tighten the meshload adjuster locknut.
(1)Hold the sector shaft.
(2)Tighten the locknut.




13.Install the steering sector shaft arm drag link castellated nut and cotter pin.
(1)Position the steering sector shaft arm drag link.
(2)Install the steering sector shaft arm drag link castellated nut.
(3)Install a new cotter pin.

14.Lower the vehicle.

NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.

15.Install the fan blade assembly and fan shroud.
16.Install the driver side air bag.



This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20