Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.

{tag}1136747325@

3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.

{tag}1136745619@

2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.

{tag}1136744242@

1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.

{tag}1136796670@

5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.

{tag}1136790719@

4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.

DISASSEMBLY
1.Remove the rear disc brake caliper.
2.Drain the remaining brake fluid from the rear disc brake caliper.
3.Secure the rear disc brake caliper in a vise.




4.Remove the caliper piston.
1Place a block of wood between the caliper bridge and the caliper piston.
2Apply low air pressure to the fluid port in the rear disc brake caliper.
3Force out the caliper piston to the block of wood.
4Remove the block of wood and the caliper piston.




5.Remove and discard the piston seal and dust boot.

NOTE: Do not hone the cylinder bore. Caliper pistons are not available for honed cylinder bores. If the rear disc brake caliper cylinder bore is excessively scored or corroded, replace the rear disc brake caliper.

ASSEMBLY

CAUTION: Never reuse the piston seal or dust boot.

NOTE: Never reuse brake fluid that has been drained from the hydraulic system or has been allowed to stand in an open container for an extended period of time.




1.Lubricate the following with High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent meeting Ford specification ESA-M6C25-A.
-Cylinder bore.
-Piston seal.
-Caliper piston.
-Dust boot.




2.Install the piston seal.




3.Install the dust boot.
4.Install the caliper piston.

CAUTION: Be careful not to damage or dislodge the piston seal.

5.Install the rear disc brake caliper.




This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20