Yandex MC
Alldata online

Alldata online. Is free

DATACENTER ERROR!!! Внимание! Авария в датацентре!!


Subscribe to the telegram channel https://t.me/kolhosniki_en

Place for your advertisement

predsedatel@kolhosniki.ru
Click for start

Diagnosis and repair



{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.

{tag}1030139050@

5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.

{tag}1030136585@

2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY

{tag}1030150546@

1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.

{tag}1030147270@

6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.

{tag}1030143799@

5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.

{tag}1029982371@

4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.

{tag}1030127370@

3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.

{tag}1029977302@


DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.





DISASSEMBLY
1.Remove the driveshaft.

2.CAUTION: Do not clamp the driveshaft in the jaws of a vise or similar holding fixture.

Place the driveshaft on a suitable workbench, being careful not to damage the tube.




3.NOTE: If components are not marked and therefore installed incorrectly, driveline imbalance can occur.

Mark the positions of the driveshaft components.




4.Clamp the U-Joint Tool in a vise.




5.Remove the snap rings.




6.NOTE: If necessary, use a pair of pliers to remove a bearing cup if it cannot be pressed out all the way.

Remove the driveshaft slip yoke.
1Position the driveshaft slip yoke in the U-Joint Tool.
2Press out a bearing cup.
3Rotate the driveshaft slip yoke.
4Press on the spider to remove the remaining bearing cup.
5Remove the driveshaft slip yoke.

7.Repeat Step 6 to remove the remaining bearing cups, spiders and driveshaft flange yoke from the driveshaft.
8.Clean the yoke area at each end of the driveshaft.

ASSEMBLY




1.Install the bearing cup.
1Start a new bearing cup into the driveshaft yoke.
2Position the new spider in the driveshaft yoke.
3Position the driveshaft in the U-Joint Tool.
4Press the bearing cup below the yoke surface.




2.NOTE: Use the yellow snap rings supplied in the kit to assemble the universal joint (U joint). If difficulty is encountered with the yellow snap rings, install the black snap rings.

Remove the driveshaft from the U-Joint Tool, and install the snap ring.

3.Repeat Steps 1 and 2 for the opposite side of the driveshaft yoke.
4.Repeat Steps 1 through 3 to install the remaining new bearing cups, spider, driveshaft slip yoke, driveshaft flange yoke and snap rings.




5.NOTE: Do not strike the bearings.

Check the U-joints for freedom of movement.
-If binding, strike the yoke with a brass or plastic hammer.
6.If necessary, use Premium Long-Life Grease XG-1-C or-K or equivalent meeting Ford Specification ESA-M1C75-B to lubricate the U-joints.
7.Install the driveshaft.




This project exists mainly due to the display of advertising.

Due to the international situation, making a profit from advertising has become impossible.

If this continues, then the project will either close completely, or become closed and paid.

To support the project, you can Buy a paid subscription


Can be closed in 20